manualshive.com logo in svg

Berker 75310002, Technical Documentation Manual, Page: 18 / 174

Share
Download
Berker 75310002 Technical Documentation Manual Download Page 18

Switch/shutter actuator 8/4gang 16A RMD 
75318003 
Switch/shutter actuator 16/8gang 16A 
RMD 
75310002 

Technical 

Documentation

 

 

 

© Berker GmbH & Co KG 2007 

 

Version: 04.04.2007 

Part 5  

(Subject to prior change)

 

 

75310002.doc

 

Seite: 18 / 174 

 

 

Controlling an output manually 

Manual control (permanent or temporary) is active. 

  Select the desired output: Press the   key briefly (if necessary, repeatedly). 

The state indicator LED of the selected output A1...A8 / A16 is flashing. In the shutter mode, the LEDs of 
an output combination are flashing. In addition, the switching state or a travel movement of the selected 
output is signalled by the status LED "ON/ " or "OFF/ " on the keypad. 

  Control the output by pressing the ON/  or the OFF/   key. 

In shutter mode: 
Brief press (< 1 s) on the ON/  or OFF/  key: stopping. 
Long press (> 1 s) on the ON/  key: upward movement or stopping. 
Long press (> 1 s) on the OFF/  key: downward movement or closing. 
In switching mode: 
Pressing the ON/  key: switching on (closing the relay contact). 
Pressing the OFF/  key: switching off (opening the relay contact). 

The selected drive motor executes the corresponding commands immediately. 

 
 

Shutting off all outputs (in shutter mode: stopping all drives) 

Permanent manual control is active: 

  Press the ALL OFF key. 

All outputs are shut off immediately (stop). The outputs are not locked. Individual activation is again 
possible after shutoff.  

  The "ALL-OFF" function is not available in temporary manual control. 

 
 

Disabling bus control of individual outputs manually 

Permanent manual control is active: 

Disabling of the bus control mode must have been enabled in the ETS. 

  Select the output: Press the  key briefly (if necessary, repeatedly). 

The state indicator LEDs of the selected output A1...A8 / A16 are flashing. In the blind/shutter mode, the 
LEDs of the output combination are flashing. In addition, the switching state or a travel movement of the 
selected output is signalled by the status LED "ON/ " or "OFF/ " on the keypad. 

  Press the   and the   key simultaneously for at least 5 s. 

The concerned output A1...A8 / A16 is locked (control via the bus not possible). 

The state indicator LEDs of the selected output A1...A8 / A16 are flashing fast. 

  To unlock, proceed in the same way. 

  An output that has been disabled manually can thereafter only be operated in the permanent manual 

mode. 

Summary of Contents for 75310002















































































































































































Reviews:

No comments