manualshive.com logo in svg

Berker 75310002, Technical Documentation Manual, Page: 166 / 174

Share
Download
Berker 75310002 Technical Documentation Manual Download Page 166

Switch/shutter actuator 8/4gang 16A RMD 
75318003 
Switch/shutter actuator 16/8gang 16A 
RMD 
75310002 

Technical 

Documentation

 

 

 

© Berker GmbH & Co KG 2007 

 

Version: 04.04.2007 

Part 5  

(Subject to prior change)

 

 

75310002.doc

 

Seite: 166 / 174 

 

 
ON-delay 
Hours (0...23)  
 

 
0...23 
 

 
This parameter is used for programming the 
duration of the ON-delay  
 
Setting the ON-delay hours.  
 

 
Minutes (0...59)  
 

 
0...59 
 

 
Setting the ON-delay minutes.  
 

 
Seconds (0...59)  
 

 
0…

30...59 

 

 
Setting the ON-delay seconds.  
 
Presetting: 30 seconds  
 

 
ON-delay retriggerable ?  

 
yes  
 
no  
 

 
An active ON-delay can be retriggered (setting 
"yes"). Alternatively, retriggering can be 
excluded (setting "no").  

  The ON-delay parameters are only visible, if 

the parameter "Activate ON-delay for 
staircase function ?" is set to "yes".  

 

 
Activate pre-warning time ?  

 
 
 
 
 
 
 
 
yes  
 
no  
 

 
When the staircase time of a staircase timer 
function has elapsed, the output can activate 
the pre-warning function. The pre-warning 
function is designed to warn a person in the 
staircase that the lights will go out shortly.  
 
The pre-warning function is activated.  
 
The pre-warning function is deactivated.  
 

 
Pre-warning time 
Minutes (0...59)  
 

 
0...59 
 

 
This parameter is used for programming the 
duration of the pre-warning time. The pre-
warning time is added to the staircase lighting 
time. Pre-warnings (shutting off the output) will 
be generated only within the pre-warning time.   
 
Setting the pre-warning time minutes.  
 

 
Seconds (0...59)  
 

 
0…

30...59 

 

 
Setting the pre-warning time seconds.  
 
Presetting: 30 seconds  

  A pre-warning time is aborted by retriggering 

of the staircase function.  

 

 
Number of pre-warnings 
(1...10)  
 

 
1…

3...10 

 

 
This parameter defines how often the output is 
to switch off within the pre-warning time. i.e. 
how many pre-warnings will be generated.  
 

Summary of Contents for 75310002















































































































































































Reviews:

No comments