manualshive.com logo in svg

Berker 75310002, Technical Documentation Manual, Page: 164 / 174

Share
Download
Berker 75310002 Technical Documentation Manual Download Page 164

Switch/shutter actuator 8/4gang 16A RMD 
75318003 
Switch/shutter actuator 16/8gang 16A 
RMD 
75310002 

Technical 

Documentation

 

 

 

© Berker GmbH & Co KG 2007 

 

Version: 04.04.2007 

Part 5  

(Subject to prior change)

 

 

75310002.doc

 

Seite: 164 / 174 

 

 
ON-delay retriggerable ?  

 
yes  
 
no  
 

 
An active ON-delay can be retriggered by 
another "1" telegram (setting "yes"). 
Alternatively, retriggering can be excluded 
(setting "no").  

  The ON-delay parameters are only visible, if 

the parameter "Selection of time delay" is set 
to "ON-delay" or to "ON- and OFF-delay".   

 

 
OFF-delay 
Hours (0...23)  
 

 
0...23 
 

 
This parameter is used for programming the 
duration of the OFF-delay  
 
Setting the OFF-delay hours.  
 

 
Minutes (0...59) 
 

 
0...59 
 

 
Setting the OFF-delay minutes.  
 

 
Seconds (0...59) 
 

 
0…

30...59 

 

 
Setting the OFF-delay seconds.  
 
Presetting: 30 seconds  
 

 
OFF-delay retriggerable ?  

 
yes  
 
no  
 

 
An active OFF-delay can be retriggered by 
another "0" telegram (setting "yes"). 
Alternatively, retriggering can be excluded 
(setting "no").  

  The OFF-delay parameters are only visible, if 

the parameter "Selection of time delay" is set 
to "OFF-delay" or to "ON- and OFF-delay". 

 

Summary of Contents for 75310002















































































































































































Reviews:

No comments