manualshive.com logo in svg

Berker 75310002, Technical Documentation Manual, Page: 143 / 174

Share
Download
Berker 75310002 Technical Documentation Manual Download Page 143

Switch/shutter actuator 8/4gang 16A RMD 
75318003 
Switch/shutter actuator 16/8gang 16A 
RMD 
75310002 

Technical 

Documentation

 

 

 

© Berker GmbH & Co KG 2007 

 

Version: 04.04.2007 

Part 5  

(Subject to prior change)

 

 

75310002.doc

 

Seite: 143 / 174 

 

 
Behaviour in case of frost 
alarm 
 

 
 
 
 
 
no reaction 
 
 
 
 
 
raising / opening the louver 
 
 
 
lowering / closing the 
louver 
 
 
 
stop 
 

 
This parameter defines the behaviour of the 
output at the beginning of the frost alarm. 
 
At the beginning of the frost alarm, the output is 
interlocked and the relay of the output shows no 
reaction. Any travel movements in progress at 
this time will still be completely finished. 
 
The actuator raises the curtain or opens the 
venting louver at the beginning of the frost 
alarm and locks the output thereafter. 
 
The actuator lowers the curtain or closes the 
venting louver at the beginning of the frost 
alarm and locks the output thereafter. 
 
At the beginning of the frost alarm, the actuator 
switches the relays of the output to "stop" and 
locks the output. A travel movement in 
progress, if any, will be interrupted. 

  This parameter is only visible, if the output 

has been assigned to the frost alarm. 

 

Summary of Contents for 75310002















































































































































































Reviews:

No comments