Berker 75310002 Page 138 Technical Documentation Manual Download | Manualshive

Page: 138 / 174

background image

Switch/shutter actuator 8/4gang 16A RMD
75318003
Switch/shutter actuator 16/8gang 16A
RMD
75310002

Technical

Documentation

© Berker GmbH & Co KG 2007

Version: 04.04.2007

Part 5

(Subject to prior change)

75310002.doc

Seite: 138 / 174

Time delay for feedback
after bus voltage return ?

yes (delay time under
"General")

no

The feedback telegram can be transmitted to
the bus with a delay after bus voltage return or
after programming with the ETS. setting "yes"
activates the feedback delay in case of bus
voltage return. The delay time is parameterized
under "General".

This parameter is only visible in case of an

actively transmitting feedback object.

Invalid blind position
feedback

no feedback

feedback object is active
signalling object

feedback object is passive
status object

The actuator can report to the bus that the
current blind position is unknown (e.g. after an
initialization, when no reference travel has been
executed as yet).

No feedback object available for the output.
Feedback deactivated.

Feedback and object are activated. The object
transmits actively (telegram transmission after
change).

Feedback and object are activated. The object
is passive (telegram transmission only as a
response to 'Read' request.

The communication flags of the object are

automatically set by the ETS according to the
setting.

This parameter is visible only in the 'Blind'

mode of operation.

Invalid shutter/awning
position feedback

no feedback

feedback object is active
signalling object

feedback object is passive
status object

The actuator can report to the bus that the
current shutter/awning position is unknown (e.g.
after an initialization, when no reference travel
has been executed as yet).

No feedback object available for the output.
Feedback deactivated.

Feedback and object are activated. The object
transmits actively (telegram transmission after
change).

Feedback and object are activated. The object
is passive (telegram transmission only as a
response to 'Read' request.

The communication flags of the object are

automatically set by the ETS according to the
setting.

This parameter is visible only in the

'Shutter/awning' mode of operation.

«
...
136
137
138
139
140
...
»

Summary of Contents for 75310002















































































































































































Reviews:

No comments

Related manuals for 75310002

Brand: ABB Pages: 7

EasySmart DGS-1100-08

Brand: D-Link Pages: 44

Brand: pathway Pages: 28

Brand: GE Pages: 302

Brand: Hama Pages: 5

SuperStack 3 4900

Brand: 3Com Pages: 2

Brand: Brightlink Pages: 33

Brand: H3C Pages: 90

LambdaUnite MSS

Brand: Lucent Technologies Pages: 388

Brand: rako Pages: 4

Brand: DAITEM Pages: 37

Brand: ASTEK Pages: 3

Brand: NTI Pages: 15

Brand: Hamlet Pages: 2

Brand: LEGRAND Pages: 30

Brand: Elements Pages: 2

Brand: Kobold Pages: 23

Brand: Pakedge Device & Software Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands