manualshive.com logo in svg

Berker 75310002, Technical Documentation Manual, Page: 131 / 174

Share
Download
Berker 75310002 Technical Documentation Manual Download Page 131

Switch/shutter actuator 8/4gang 16A RMD 
75318003 
Switch/shutter actuator 16/8gang 16A 
RMD 
75310002 

Technical 

Documentation

 

 

 

© Berker GmbH & Co KG 2007 

 

Version: 04.04.2007 

Part 5  

(Subject to prior change)

 

 

75310002.doc

 

Seite: 131 / 174 

 

 
Position of blind on return of 
bus/mains voltage (0...100 
%) 
 

 
0...100 

 
This parameter specifies the blind position to be 
approached in case of bus or mains voltage 
return. 

  This parameter is only visible, if "Behaviour in 

case of bus or mains voltage return" is set to 
"approach position". 

  This parameter is visible only in the 'Blind' 

mode of operation. 

 
Position of slat on return of 
bus/mains voltage (0...100 
%) 
 

 
0...100 

 
This parameter specifies the slat position to be 
approached in case of bus or mains voltage 
return after the blind has been positioned at the 
desired height. 

  This parameter is only visible, if "Behaviour in 

case of bus or mains voltage return" is set to 
"approach position". 

  This parameter is visible only in the 'Blind' 

mode of operation. 

 
Position of shutter/awning 
on return of bus/mains 
voltage (0...100%) 
 

 
0...100 

 
This parameter specifies the shutter or awning 
position to be approached in case of bus or 
mains voltage return. 

  This parameter is only visible, if "Behaviour in 

case of bus or mains voltage return" is set to 
"approach position". 

  This parameter is visible only in the 

'Shutter/awning' mode of operation. 

 
Position of venting louver 
on return of bus/mains 
voltage (0...100%) 
 

 
0...100 

 
This parameter specifies the venting louver 
position to be approached in case of bus or 
mains voltage return. 

  This parameter is only visible, if "Behaviour in 

case of bus or mains voltage return" is set to 
"approach position". 

  This parameter is visible only in the 'Venting 

louver' mode of operation. 

 
Travelling time extension 
for upward travel 
 

 
none 
2 % 
3 % 
4 % 
5 % 
6 % 
7 % 
8 % 
9 % 
10 % 
12.5 % 
 

 
The switching/shutter actuator prolongs all 
upward movements or venting louver 
movements into the open position based on the 
time extension specified in this parameter. The 
time extension expressed in percent is the 
difference between the measured travel time 
needed to reach the lower end position 
(completely closed position) and the time 
needed to reach the upper end position 
(completely open position). 

  This parameter is only visible, when the 

automatic end position detection is not 
deactivated.  

 

Summary of Contents for 75310002















































































































































































Reviews:

No comments