manualshive.com logo in svg

Berker 75310002, Technical Documentation Manual, Page: 126 / 174

Share
Download
Berker 75310002 Technical Documentation Manual Download Page 126

Switch/shutter actuator 8/4gang 16A RMD 
75318003 
Switch/shutter actuator 16/8gang 16A 
RMD 
75310002 

Technical 

Documentation

 

 

 

© Berker GmbH & Co KG 2007 

 

Version: 04.04.2007 

Part 5  

(Subject to prior change)

 

 

75310002.doc

 

Seite: 126 / 174 

 

 
Behaviour at the end of 
permanent manual control 
during bus operation 

 
 
 
 
 
no change 
 
 
 
 
 
 
 
 
 
 
 
 
output tracking 
 

 
The behaviour of the actuator at the end of 
permanent manual control depends on this 
parameter. 
 
All telegrams received during an active 
permanent manual control mode for direct 
operation (long-time/short-time, positioning,  
scenes) are be rejected. After the end of the 
permanent manual control mode, the current 
state of all outputs remains unchanged. If, 
however, a function with a higher priority is 
being activated during manual control (safety, 
forced position, sun protection), the actuator 
activates the higher-ranking function for the 
corresponding outputs. 
 
During an active permanent manual control all 
incoming telegrams (short-time telegrams 
excepted) are internally tracked. At the end of 
manual control, the outputs are adjusted 
accordingly. 
 

 
Disable bus control of 
individual outputs during 
bus operation? 

 
yes 
 
no 
 

 
Individual outputs can be disabled locally during 
permanent manual control so that the disabled 
outputs can no longer be controlled via the bus. 
Disabling by means of manual control is only 
permitted if this parameter is set to "yes" 
 

Summary of Contents for 75310002















































































































































































Reviews:

No comments