manualshive.com logo in svg

Berker 75310002, Technical Documentation Manual, Page: 123 / 174

Share
Download
Berker 75310002 Technical Documentation Manual Download Page 123

Switch/shutter actuator 8/4gang 16A RMD 
75318003 
Switch/shutter actuator 16/8gang 16A 
RMD 
75310002 

Technical 

Documentation

 

 

 

© Berker GmbH & Co KG 2007 

 

Version: 04.04.2007 

Part 5  

(Subject to prior change)

 

 

75310002.doc

 

Seite: 123 / 174 

 

 
Description: 

Values: 

Remarks: 

  Shutter outputs safety times 

 
Use wind alarm monitoring 
function ? 
(only if wind alarms are 
enabled!) 
 

 
yes 
 
no 
 

 
If the wind alarms enabled under "Shutter 
outputs safety" are to be monitored cyclically for 
incoming telegrams to the safety objects, the 
monitoring function must be enabled here 
(setting: "yes").  
In the opposite case (setting: "no"), the objects 
are not monitored cyclically . 

  As soon as the monitoring function is 

activated, telegrams must be transmitted 
cyclically to all enabled wind alarm objects. 

  The monitoring function may only be 

activated, if at least one wind alarm has been 
activated under "Shutter outputs safety". 

 

 
Wind alarm monitoring time 
Hours (0...23) 
 

 
0...23 
 

 
This parameter is used for programming the 
wind alarm monitoring time. 
 
Sets the monitoring time hours. 
 

 
Minutes (1...59) 
 

 
1...

25 - 59 

 

 
Sets the monitoring time minutes. 
 
Presetting: 25 minutes 
 

  The cycle time of the transmitter should be 

less than half the parameterized monitoring 
time of the actuator. 

  The times can only be set, if wind alarm 

monitoring is activated. 

 

 
Use rain alarm monitoring 
function ? 
 

 
yes 
 
no 
 

 
If the rain alarm enabled under "Shutter outputs 
safety" is to be monitored cyclically for incoming 
telegrams to the safety object, the monitoring 
function must be enabled here (setting: "yes"). 
In the opposite case (setting: "no"), the object is 
not monitored cyclically . 

  As soon as the monitoring function is 

activated, telegrams must be transmitted 
cyclically to the enabled rain alarm object. 

  The parameter is only visible, if the rain alarm 

has been enabled under "Shutter outputs 
safety". 

 

 
Rain alarm monitoring time 
Hours (0...23) 
 

 
0...23 
 

 
This parameter is used for programming the 
rain alarm monitoring time. 
 
Sets the monitoring time hours. 
 

Summary of Contents for 75310002















































































































































































Reviews:

No comments