Berker 75310002 Page 122 Technical Documentation Manual Download

Page: 122 / 174

Switch/shutter actuator 8/4gang 16A RMD
75318003
Switch/shutter actuator 16/8gang 16A
RMD
75310002

Technical

Documentation

Version: 04.04.2007

Part 5

(Subject to prior change)

75310002.doc

Seite: 122 / 174

Priority of safety alarms

wind

rain

frost

wind

frost

rain

wind

frost

rain

frost

wind

frost

rain

wind

frost

wind

rain

This parameter defines the priority ranking of
the individual safety alarms.
Interpretation: high

medium

low.

The three wind alarms have the same priority

with respect to one another.

The safety alarm enabling parameters and

the priority parameter is only visible when the
safety functions are enabled.

Summary of Contents for 75310002















































































































































































Search results

Summary of Contents for 75310002

Reviews:

Related manuals for 75310002

Brands by name

Popular brands

Berker 75310002, Technical Documentation Manual

Search results

Summary of Contents for 75310002

Reviews:

Related manuals for 75310002

Brands by name

Popular brands