manualshive.com logo in svg

Berker 75310002, Technical Documentation Manual, Page: 117 / 174

Share
Download
Berker 75310002 Technical Documentation Manual Download Page 117

Switch/shutter actuator 8/4gang 16A RMD 
75318003 
Switch/shutter actuator 16/8gang 16A 
RMD 
75310002 

Technical 

Documentation

 

 

 

© Berker GmbH & Co KG 2007 

 

Version: 04.04.2007 

Part 5  

(Subject to prior change)

 

 

75310002.doc

 

Seite: 117 / 174 

 

 

Presetting the fabric-stretching function 

The fabric-stretching function can be parameterized independently for each shutter or awning output on 
parameter page "Ax – Fabric-stretching" (x = number of output). The travel time required for fabric 
stretching by means of a movement in opposite direction can be parameterized. 

The fabric-stretching function must be activated. 

  Select the desired value for the "Time for fabric-stretching" parameter. 

After the end of a downward travel the curtain stops and – after elapsing of the changeover delay – 
moves backwards in opposite direction for a period corresponding to the parameterized fabric-stretching 
time. 

 

  The time for fabric stretching must be selected shorter than the parameterized or measured travel time of 

the shutter or awning. Otherwise, risk of malfunction. 

  Fabric stretching will only be effected if the downward movement lasts longer than the parameterized 

fabric-stretching time. 

 

4.2.4.3 

Delivery state 

In the state as delivered, the actuator is passive, i.e. no telegrams are transmitted to the bus. The outputs 
can, however, be operated by manual control on the device, if the mains voltage is on. In the manual control 
mode, no feedback telegrams are sent to the bus. All other functions of the actuator are deactivated. 

The device can be programmed and put into operation with the ETS. The physical address is preset to 
15.15.255. 

 
Moreover the device has been configured at the factory with the following characteristics...  

–

  Channel definition: all outputs configured for shutter operation 

–

  Travel time (continuous run): 1 minute 

–

  Travel time extension 2 % 

–

  Break during travel direction changeover 1 s 

–

  Response to bus voltage failure: no reaction 

–

  Behaviour on return of bus or mains voltage: stop 

Summary of Contents for 75310002















































































































































































Reviews:

No comments