manualshive.com logo in svg

Berker 75310002, Technical Documentation Manual, Page: 116 / 174

Share
Download
Berker 75310002 Technical Documentation Manual Download Page 116

Switch/shutter actuator 8/4gang 16A RMD 
75318003 
Switch/shutter actuator 16/8gang 16A 
RMD 
75310002 

Technical 

Documentation

 

 

 

© Berker GmbH & Co KG 2007 

 

Version: 04.04.2007 

Part 5  

(Subject to prior change)

 

 

75310002.doc

 

Seite: 116 / 174 

 

 

'Fabric-stretching' function 

In the shutter/awning mode of operation, the Fabric-stretching function can be activated. The Fabric-
stretching function permits stretching the fabric of an awning tight after lowering. The fabric-stretching 
function can also be used with shutters to re-open the slits of the shutter curtain after a downward 
movement into the lower end position. 

If activated in the ETS parameters, fabric stretching is executed during each downward travel after stopping 
and after the parameterized changeover delay has elapsed. The curtain is then 'stretched' by moving briefly 
into the opposite travel direction (cf. Fig. 40). 
 
 

downward travel

brickwork

awning-case

fabric

awning linkage

fabric-stretching travel

fabric (stretched)

brickwork

awning-case

awning linkage

 

Fig. 40: Fabric-stretching in an awning 

 

The downward travel can be triggered by any of the following events: Long-time, short-time or position 
telegram, forced position, safety or sun protection function, central telegram or scene recall and also the 
manual control. 

Sheet- stretching is never effected in upward travel movements. 
 

  Fabric stretching affects the determination of positions and the position feedback since a fabric-stretching 

movement changes the position of a shutter or an awning. In a positioning move into the lower end 
position (100 %), the position value reported back after the fabric-stretching operation will always be a 
smaller one. 

 

Fabric-stretching cannot be parameterized in the blind or louver modes of operation.

 

 

 

Activating the fabric-stretching function  

The fabric-stretching function can be activated independently for each shutter or awning output on 
parameter page "Ax – Enabled functions" (x = number of output). 

The mode of operation selected must be the "Shutter/awning" mode. 

  Set the parameter "Fabric-stretching function" to "enabled". 

Parameter page "Ax – Fabric-stretching" is enabled and the fabric-stretching function is activated. 

 

  Fabric-stretching cannot be parameterized in the blind or louver modes of operation. 

Summary of Contents for 75310002















































































































































































Reviews:

No comments