manualshive.com logo in svg

Berker 75310002, Technical Documentation Manual, Page: 10 / 174

Share
Download
Berker 75310002 Technical Documentation Manual Download Page 10

Switch/shutter actuator 8/4gang 16A RMD 
75318003 
Switch/shutter actuator 16/8gang 16A 
RMD 
75310002 

Technical 

Documentation

 

 

 

© Berker GmbH & Co KG 2007 

 

Version: 04.04.2007 

Part 5  

(Subject to prior change)

 

 

75310002.doc

 

Seite: 10 / 174 

 

 

Installing / removing the protective cap 

To protect the bus lines against hazardous voltages, especially in the area of the connecting terminals, a 
protective cap can be installed. 

The cap is installed with the bus terminal in place and the connected bus line led out at the rear. 

  To install the cap: slide the cap over the bus connecting terminal until it is heard to engage 

(cf. Fig. 4.A). 

  To remove the cap: Remove the cap by pressing the sides slightly and by pulling it out to the front 

(cf. Fig. 4.B). 

 

A

B

 

Fig. 4: Installing / removing the protective cap 

Summary of Contents for 75310002















































































































































































Reviews:

No comments