manualshive.com logo in svg

BERGHOF B-PRIMIS DC-PRIME DC2110W X CM, User Handbook Manual

Share
Download
BERGHOF B-PRIMIS DC-PRIME DC2110W X CM User Handbook Manual Download Page 69

USER HANDBOOK 1.2 | B-PRIMIS DC/ET PRIME 2110W X C, 2115WUX C 

Berghof Automation GmbH | Harretstraße 1 | 72800 Eningen | www.berghof-automation.com 
270011X00_B-PRIMIS_ET-DC-PRIME 2110W-2115W_EN.docx  
 

 

 

69

 

10.2. ET2115 Ethernet TerminalWUX CS / ET2110W X CS 

Ethernet Terminal 

ET2115WUX CS 

ET2110W X CS 

Display 

FHD 

WXGA 

Across diagonals 

15.6" 

10.1" 

Item no. 

222003100 

222003200 

Resolution 

1920 x 1080 pixels 

1280 x 800 pixels

 

Colours 

TFT: 16.7 M 

CPU 

CPU 

i.MX6 800 MHz / Single Core 

Dimensions and weight 

Dimensions (WxHxD) 

392 x 241 x 55 mm 

259 x 177 x 55 mm 

Weight 

approx. 3 kg 

approx. 2.5 kg  

Operating conditions 

Operating temperature 

0 °C to 55 °C (front and rear of the device; in compliance with installa-

tion requirements) 

Relative humidity 

max. 85%, non-condensing 

Transport and storage 

Operating temperature 

–20 °C to +70 °C 

Relative humidity 

max. 85%, non-condensing 

Operation 

Installation 

Removable securing clips 

Certification 

to product standards EN 61010-2-201, EN 61131-2 

Touch operation 

Touch capacitive (single-touch) 

Shock resistance 

Vibration 

sinusoidal (EN 60068-2-

6) test: Fc 10…150 Hz, 10 m/s² 

Shock 

15 G (approx. 150 m/s²), 11 ms duration, sinusoidal half-wave (EN 

60068-2-27)  

Test: Ea 

EMC, protection rating 

Emitted interference 

EN 61131-2 

Resistance to interference 

EN 61131-2, industrial zone 

Protection class 

III 

Summary of Contents for B-PRIMIS DC-PRIME DC2110W X CM














































































Reviews:

No comments

Brands by name

Popular brands

Load more brands