manualshive.com logo in svg

BERGHOF B-PRIMIS DC-PRIME DC2110W X CM, User Handbook Manual

Share
Download
BERGHOF B-PRIMIS DC-PRIME DC2110W X CM User Handbook Manual Download Page 66

USER HANDBOOK 1.2 | B-PRIMIS DC/ET PRIME 2110W X C, 2115WUX C 

Berghof Automation GmbH | Harretstraße 1 | 72800 Eningen | 

www.berghof-automation.com

 

270011X00_B-PRIMIS_ET-DC-PRIME 2110W-2115W_EN.docx 

 

66

 

10. 

Technical data 

10.1. DC2115WUX CM / DC2110W X CM Dialog Controller 

Dialog Controller 

DC2115WUX CM 

DC2110W X CM 

Display 

FHD 

WXGA 

Across diagonals 

15.6" 

10.1" 

Item no. 

270011300 

270011200

 

Resolution 

1920 x 1080 pixels 

1280 x 800 pixels

 

Colours 

TFT: 16.7 M 

CPU, user memory 

CPU 

800 MHz ARM

®

 

with Cortex™-A9 single core 

Program memory (flash) 

512 MB (max. 2048 MB) 

Program memory and data 

memory (RAM) 

512 MB 

Non-volatile memory (FRAM) 

100 kB 

Dimensions and weight 

Dimensions (WxHxD) 

392 x 242 x 55 mm 

259 x 177 x 55 mm 

Weight 

approx. 3 kg 

approx. 2.5 kg 

Operating conditions 

Operating temperature 

0 °C to 55 °C (front and rear of the device; in compliance with installa-

tion requirements) 

Relative humidity 

max. 85%, non-condensing 

Transport and storage 

Operating temperature 

–20 °C to +70 °C 

Relative humidity 

max. 85%, non-condensing 

Operation 

Installation 

removable securing clips 

Certification 

to product standards EN 61010-2-201, EN 61131-2 

Development environment 

CODESYS V3 (IEC 61131-3) 

Protocols 

Standard EtherCAT master, CANopen master 

Optional: Modbus RTU M/S, Modbus TCP M/S, SNMP, OPC UA, 

Ethernet/IP, PROFINET, BACnet 

Visualisation 

Target Visu (Display), Web Visu (Web Server, HTML5) 

Touch operation 

Touch capacitive (multi-touch) 

Summary of Contents for B-PRIMIS DC-PRIME DC2110W X CM














































































Reviews:

No comments

Brands by name

Popular brands

Load more brands