Berg Engineering & Sales Company NS-11006 Instruction Manual Download Page 9

Page: 9 / 90

Device Connections, On/Off-Switch

NewSonic SonoDur-R

Issue 105 06/2020

Page 9

Device Connections, On/Off-Switch

All device connections and the on/off switch is located on the rear site of the instrument.

Figure 3.1

Nr.

Kurzbezeichnung

Beschreibung

On / Off

Power Switch

Digital I/O

Digital Input / Output signals, galvanically isolated

USB

USB (Device) interface, suitable for software updates,
manual file transfer

COM1

Serial Interface RS232, data output and remote
control, galvanically isolated

COM2

No function, for future extensions

24V DCin

Input power, 24V DC / 1A min.

Probe

Connector for probe cable, coded and with lock
mechanism (Push-Pull)

LAN

LAN interface (no function, for future extensions)

Table 3-1

Summary of Contents for NS-11006



























































































Search results

Summary of Contents for NS-11006

Reviews:

Related manuals for NS-11006

Brands by name

Popular brands

Berg Engineering & Sales Company NS-11006, Instruction Manual

Search results

Summary of Contents for NS-11006

Reviews:

Related manuals for NS-11006

Brands by name

Popular brands