Berbel Smartline BWH 90 ST Page 22 Operating And Installation Instructions Download | Manualshive

Page: 22 / 32

background image

22

Operation

6005738_0 – 25.03.2021

4.2.5

Check filter filling indicator

The device has a control indicator to remind the operator
to change the filter filling. If no air circulation filter is used,
the control indicator has no meaning.
The control indicator flashes every 1,000 fan operating hours.
The hours counter is started anew by switching off the
control indicator.

Button

Function

After switching off, the button flashes for
2 minutes:
The filter filling must be replaced.

D

“6.2.2 Replacing filter filling (with
recirculating and hybrid mode)”
(page 25).

When the filter filling has been changed:

☞

Press the button (> 1 second).

The hour counter restarts, and the flashing
indicator turns off.

«
...
20
21
22
23
24
...
»

Summary of Contents for Smartline BWH 90 ST

































Reviews:

No comments

Related manuals for Smartline BWH 90 ST

Brand: Halton Pages: 28

Brand: Futuro Futuro Pages: 10

Brand: Gaggenau Pages: 124

Brand: Gaggenau Pages: 16

Brand: Pelgrim Pages: 36

Brand: Malloca Pages: 20

Brand: ELICA Pages: 10

Brand: V-ZUG Pages: 24

Diamante DIAM36SS

Brand: Faber Pages: 20

Brand: Best Pages: 48

Brand: ElectrIQ Pages: 15

Roma Island ZRM-E36AS

Brand: Zephyr Pages: 19

Brand: Haier Pages: 14

Brand: Haier Pages: 56

Brand: Haier Pages: 24

Brand: Haier Pages: 40

Brand: Haier Pages: 51

Brand: Haier Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands