Berbel Smartline BWH 90 ST Page 11 Operating And Installation Instructions Download | Manualshive

Page: 11 / 32

background image

11

Installation

6005738_0 – 25.03.2021

EN

3.5.3

Removing the lower section and separating

unit

D

ATTENTION!

Danger of property damage through falling parts!

When working on the device, parts of the device or tools
could fall and damage the kitchen equipment.

☞

Protect the cooled hob and other surfaces in the cooking
area (e.g. with thick cardboard).

☞

Fold the lower section down.

☞

Press the lower section at the side with both hands and
draw it approx. 10 mm down to unlatch it.

☞

Move the lower section forwards in an arc and remove it.

The separating unit is inserted and is held in the device by
side hooks.

☞

Pull the side hooks inwards on both sides.

☞

Remove the separating unit.

«
...
9
10
11
12
13
...
»

Summary of Contents for Smartline BWH 90 ST

































Reviews:

No comments

Related manuals for Smartline BWH 90 ST

Brand: GE Pages: 48

Brand: Westinghouse Pages: 20

Brand: U.S. Products Pages: 8

Brand: Ariafina Pages: 36

Brand: Faber hoods Pages: 112

Brand: F.Bertazzoni Pages: 12

Brand: Faber Pages: 2

Brand: Jenn-Air Pages: 32

Brand: Robam Pages: 12

AiroClearWall V4000

Brand: V-ZUG Pages: 24

Brand: NuTone Pages: 28

Brand: arietta Pages: 36

Brand: Beko Pages: 40

Brand: Beko Pages: 20

Brand: Beko Pages: 44

Brand: Beko Pages: 44

Brand: Beko Pages: 74

Brand: Beko Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands