Bentel Security KYO 100, User Manual

Page: 18 / 24

USER MANUAL 18
Š Š
The Partitions that are not controlled by the Reader will
not affect the LEDs.
If the configuration of the Armed Partitions does not match
either A or B Mode Arming (for example, one of the Reader
Partitions has been Armed via Keypad), neither the Am-
ber nor Green LED will turn ON.
The Installer can program the Reader LEDs to sig-
nal the System status at all times, or alternatively,
only in response to a Valid Key/Card (LEDs OFF
when no Key/Card is present).
Key/Card at Reader
When a Key/Card is present at the Reader, the LEDs
will signal as follows.
a) Fast Blinking on 1 LED - Before Arming the Parti-
tions, the Control panel will check the status of the
Unbypassed (ON) and Instant Zones. If a Zone is ‘Vio-
lated’ (e.g. door or window open), the LED, associ-
ated with the selected Arming Mode, will blink quickly.
If this occurs, DO NOT ARM the System, as Arming
will trigger a False Alarm.
It takes the Control panel about 2 seconds to check
all the Zones.
False Alarms can be stopped by simply Disarming
the system (refer to “Digital Key/Card Reader opera-
tions” in this section). If you accidentally trigger an
Alarm, call the Central Station to prevent the opera-
tor from taking unnecessary action.
If, when you Arm the system, the Control panel de-
tects
Autobypassable zones in Alarm status, it will
bypass them automatically. In this way, false Alarms
will not be triggered, however, Bypassed zones will
be UnBypassed automatically when their Partitions
are next disarmed.
b) Fast Blinking on all 3 LEDs - This will occur when a
False Key/Card is present at the Reader.
c) Slow Blinking on all 3 LEDs (ECLIPSE Readers
only) - This Mode will allow you to restore the previ-
ous setting (reset the Arming Mode that was active
before the SAT Key was inserted. To Reset: push
the SAT Key into the ECLIPSE Reader until the 3
LEDs start to blink slowly, the previous setting will
be restored when you remove the Key.
b) Red LED ON - The System will Arm when you re-
move the Key/Card from the Reader.
e) Amber LED ON - The System will Arm in A Mode
when you remove the Key/Card from the Reader.
f) Green LED ON - The System will Arm in B Mode
when you remove the Key/Card from the Reader.
Your Installer may have Disabled the Reader LEDs,
therefore, they will not turn ON even when a valid
Key/Card is used.
Multiple Systems
The Digital Keys/Cards can be programmed (by the In-
staller) to operate on more than one System, and to
manage different Partitions on each System.
Digital Key/Card operations
The Digital Keys/Cards can:
Arm — Global Mode
Disarm
Arm — A Mode
Arm — B Mode
Stop Alarms
Arm/Disarm Patrol
Your Installer may have programmed some “restricted”
Digital Keys/Cards. These Keys/Cards will be allowed
to perform a maximum number of operations (from 1
to 254) after which, they will be Disabled automati-
cally. Disabled “restricted” Digital Keys/Cards can
be re-enabled and refreshed with the same number
of operations via the User Menu (refer to Enable/
Disable Key/Card).
TBUVWO}OHOVWIOaLNL~EOnDLROGFOYQimeNpSONLO^QNSQp
`Y_ FTNTXW LMNOPOQ
VY_
_
\MMGLRGOKEGcEHJEDGCHDOUOULIFGHDEG^UFHDVEJ
_c
\OGMEHFOGLIEGLRGOKEGcEHJEDGCHDOUOULIFGUFG\DVEJ
aCFn
UCDG€DGg
\OGMEHFOGLIEG\MHDVGLDG`HVSEDGEfEIOGKHFGNEEIGJEOEXOEJGLIGLIEGLRGOKEGcEHJEDGCHDOUOULIF
HIJG\bbGOKEGcEHJEDGCHDOUOULIFGHDEG^UFHDVEJ
NEL
UCDG€DGg
\OGMEHFOGLIEG\MHDVGLDG`HVSEDGEfEIOGKHFGNEEIGJEOEXOEJGLIGLIEGLRGOKEGcEHJEDGCHDOUOULIF
HIJG\`Gbg\_`GahgGLRGOKEGcEHJEDGCHDOUOULIFGUFG\DVEJ
aY``\p
_c
`KEGcEHJEDGCHDOUOULIFGHDEG\DVEJGUIGG ' GdLJE
_
`KEG\DVEJq^UFHDVEJGFOHOeFGLRGOKEGcEHJEDGCHDOUOULIFGJLEFGILOGVHOXKGGG ' dLJE
qVYY^
_c
`KEGcEHJEDGCHDOUOULIFGHDEG\DVEJGGUIGG dLJE
_
`KEG\DVEJq^UFHDVEJGFOHOeFGLRGOKEGcEHJEDGCHDOUOULIFGJLEFGILOGVHOXKGGG dLJE