background image

 
 

9.0 Reference Information  

 

    

Doc/Ref                                                               Title/Subject

              

 
 
 BS 5410       Part 1 ; 1977 and Part 2 ; 1978       Code of Practice for oil firing    
                                                      
BS EN 292      Parts 1 and 2; 1992                       Safety of Machinery                      
                                                       
BS EN 60204   Part 1; 1993                                 Safety of Machinery - Electrical        
                                                       
BS EN 60335   Part 1; 1988                                 Safety of Electrical Appliances         
                                                      
BS EN 55014   1993                                            Electromagnetic Compatibility           
  
BS EN 50165   1995                                           Safety of Electrical Equipment           
                                                      
BS 5854         1980                                             Code of Practice - Flues/Flue Structures 
                                                        
BS 799        Part 5 ; 1987                                    Oil Burning Equipment - oil tanks        
               
OFTEC         OFS T-100                                     Polyethylene oil storage tanks           
                                                     
BS 715         1993                                                Metal Flue Pipes and Fittings           
                                                        
BS 5440        Part 1 ; 1990                                   Specification/Installation of Flues      
                                                        
BS 5440        Part 2 ; 1989                                  Ventilation Requirements Gas Appliances  
 
BS 779         Part 2 ; 1991                                   Oil burning equipment - burners         
                                                      
ISO 228/1     See also BS 2779 and BS 5380)     Pipe Threads Seals and Couplings        
                                                                                                           
                                                       

                                                       
                                                      
                                                    
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for MH300



























Reviews: