background image

EN-1

FCC Notice

This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in residential installation.
This equipment generates, uses and can radiate radio frequency energy and if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, detectable by turning the equipment in question off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:

„

Reorient or relocate the receiving antenna

„

Increase the distance between the equipment and the receiver

„

Connect the equipment to an outlet on a different circuit than that which the receiver

is connected to

„

Or consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to following
two conditions:
1.

This device may not cause harmful interference, and 

2.

This device must accept any interference that may cause undesired operation.

http://www.pureglare.com.au

Summary of Contents for MP514




























Reviews: