Benning 044166 Operating Manual Download Page 10

2.4 Intended use

Safety

5186 / 07/2021 en

BENNING CC 4-1 / CC 4-2

10

2.4

Intended use

Only use the device within the framework of the corresponding technical data. Any operating
conditions that deviate from this shall be considered as improper use. Solely the user of the
device shall be liable for any resulting damage.

In particular, note the following:

• In case of improper use, the liability and warranty claims become void. Solely the user of the

device shall be liable for any damage resulting from improper use. Uses not complying with
the intended use include e. g.:

– Use of components, accessories, spare or replacement parts that have not been

released and approved for the respective application by Benning

– Non-observance, manipulation, changes or misuse of the operating manual or the

instructions and notes contained therein

– Any form of misuse of the device

– Any use other than or beyond that described in this operating manual

• Warranty and liability claims are generally excluded if damage is due to force majeure.

• If any prescribed services are not performed regularly or not on time according to

manufacturer specifications during the warranty period, a decision about a warranty claim
can only be made once the findings are available.

Direct any questions to Technical Support [

}

 page 7].

Using the device

Please observe the following basic obligations when using the device:

• The device may only be used in a technically perfect and safe condition. Always check the

device for damages before using it.

• Make sure the personnel using the device is qualified for the respective task.

• Observe relevant regulations on occupational safety and health as well as those on

environmental protection.

• The device may only be used in dry environments.

• Use the device only in electric circuits of overvoltage category III with a conductor for a

maximum of 600 V‑AC to earth.

• Do not apply any voltage to the outputs of the device.

 WARNING

Opening the device

Danger to life or serious injury is possible due to contact with high electric voltage when opening
the device. The device might get damaged.

• Do not open the device.

• Please contact your specialty retailer or the returns management [

}

 page 7] for any repairs.

Summary of Contents for 044166























Reviews: