manualshive.com logo in svg

Benefon SERAPH NT, Operating Instructions Manual

Share
Download
Benefon SERAPH NT Operating Instructions Manual Download Page 44

PART D: POWER MANAGEMENT

44 POWER SUPPLY

PART D: POWER MANAGEMENT 

POWER SUPPLY

•Mains charger CMA-70-230 (with the cable FMC-70)

•Cigarrette lighter charger CCS-71-12

•Standard Li-Ion batteries 

 -

650 mAh (BBL77S)

 -

900 mAh (BBL77N)

 -

1200 mAh (BBL77P)

 -

1700 mAh (BBL77G). 

The battery type may vary depending on the market area and
sales package. In unclear cases, check the battery compati-
bility with the dealer. 

MAINS CHARGER 

The mains charger should only be used indoors. Make sure
that the voltage in the country which you are staying corre-
sponds to the voltage (230 V) of the charger.

When charging, connect the charger (round) end of the ca-
ble into the charger and lock it by turning it half a turn
clockwise. Plug the square end of the cable (with the arrow
facing up) into the system connector on the device. 

Plug the charger into a mains outlet. Charging will start au-
tomatically.

The mains charger is provided with the device, but is also
available from the assortment of Benefon accessories. For
more information on other charger types, see 

PART E: ACCES-

SORIES ON PAGE 46

.

CHARGING

The battery must be fully charged before taken into use. The
battery will reach its full capacity only after two or three
charging times.  

The device controls the charging status, the battery temper-
ature and power supply during the charging operation.  

Summary of Contents for SERAPH NT

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands