background image

5554-513

22" ELECTRIC SNOW BLOWER

6

When working outdoors with a product, use an extension cord that is designed for 

outside use. This type of cord is designated with "WM" on the cord's jacket.
Before using any extension cord, inspect it 

for loose or exposed wires and cut or worn 

insulation. It is possible to tie the extension 

cord and power cord in a knot to prevent 

them from becoming disconnected during 

use. Make the knot as shown in the figure at 

right, then connect the plug end of the power 

cord into the receptacle end of the extension 

cord. This method can also be used to tie two 

extension cords together.

WARNING! The double-insulated system is intended to protect the user 

from shock resulting from a break in the snow blower's internal insulation. 

Observe all normal safety precautions to avoid electrical shock.

•  Inspect the extension cord and the power cord on a regular basis. Look for 

deterioration, cuts, or cracks in the insulation. Inspect the connections for 

damage. Repair or replace the extension cord or the power cord if any damage  

is found.

•  Verify that the paddle and all moving parts have come to a complete stop, and 

disconnect the snow blower from the power supply in order to prevent accidental 

start-ups, before cleaning or performing any inspections or repairs.

•  Do not abuse the extension cord. Do not carry the snow blower by the power cord 

or pull on the cord in order to disconnect it from the receptacle.

•  Keep the extension cord away from heat, oil, and sharp edges in order to prevent 

damage.

•  If the extension cord is damaged in any manner while it is plugged in, disconnect 

it from the outlet immediately.

•  Prevent any possible disconnection of the power cord from the extension cord 

while the snow blower is in use by using the cord retainer. Refer to the section 

entitled Using the Cord Retainer.

•  Unplug the snow blower and allow it to cool down before putting it into storage. 

Store the snow blower indoors.

•  Unplug the snow blower when it is not in use and before performing any 

maintenance or repairs.

WARNING! Keep the extension cord clear of the working area. Position the 

cord so that it will not get caught on obstacles while you are operating the snow 

blower. Failure to do so can result in serious personal injury.

Summary of Contents for 5554-513

























Reviews: