background image

5554-513

22" ELECTRIC SNOW BLOWER

4

•  Keep guards in place and in working order.
•  Don't force the snow blower - It will perform better and safer at the rate for which 

it was designed.

•  Don't overreach - Keep proper footing and balance at all times.
•  If the snow blower strikes a foreign object, follow these steps:
 

i) Stop the snow blower. Release the switch.

 

ii) Unplug power cord.

 

iii) Inspect for damage.

 

iv) Repair any damage before restarting and operating the snow blower.

•  Store snow blower indoors -When not in use, power tools should be stored indoors 

in a dry, locked-up place out of reach of children.

•  Maintain snow blower with care - Follow instructions for lubricating and changing 

accessories.

•  Allow the snow blower to run for a few minutes after clearing snow in order to 

prevent moving parts from freezing.

•  Only use identical replacement parts and accessories for this snow blower. The 

use of nonidentical or accessories could lead to serious injury to the user or 

damage the snow blower, and will void the warranty.

•  Do not pick up the snow blower while it is running. The snow blower is designed to 

travel along the ground.

•  Never allow children to operate a snow blower. Keep the area of operation clear of 

all persons, particularly small children, and pets.

•  Thoroughly inspect the area where the equipment is to be used and remove all 

stones, sticks, wires, bones, and other foreign objects.

•  Stop the paddle when crossing gravel driveways, walkways, or roads.
•  To prevent disconnection of the power cord from the extension cord during 

operation. Refer to the section entitled Using the Cord Retainer.

•  Avoid accidental starting - Don't carry a plugged in snow blower with your finger 

on the switch. Be sure switch is off when plugging in.

•  If the cord is damaged in any manner while it is plugged in, disconnect it from the 

outlet immediately.

•  Do not abuse the cord. Do not carry the snow blower by the power cord or yank 

the cord in order to disconnect it from the receptacle.

•  Disconnect the snow blower from the power supply when: not in use, before 

servicing, and when changing accessories.

GENERAL SAFETY RULES

•  Verify that the snow blower is secure while transporting.
•  Store the snow blower in a dry area that will prevent unauthorized use or damage. 

Keep out of the reach of children.

•  Keep handles dry, clean, and free of debris. Clean the snow blower after each use. 

Refer to Maintenance section in this manual for more information.

•  If the labels on the snow blower become defaced or start to lift off, contact the 

toll-free helpline at 1-833-818-4111.

Summary of Contents for 5554-513

























Reviews: