background image

Reference Manual 
 
Power Analyzer EMM5 

 

Rev. 11 

 

 

2018-07 

 

11 

 

odd harmonics on the left side, even harmonics on the right. The numbers before the harmonic value gives the order of 

the harmonic (01 = fundamental wave).   

KEYS: 

 

Left key (“M”) switches back to main menu 

 

” - key scrolls the list of harmonics down to the harmonics of higher order  

 

” - key scrolls the list back to the top (lower harmonics) 

 

Right key (“

”) switches between the seven data sources (4 currents and 3 voltages) 

 

If the harmonic display quotes "NOT AVAILABLE", the current or voltage, which sources the harmonic 

calculation is below a certain limit or even not present. This makes the FFT calculation of the harmonics 

very inaccurate or impossible. 

The contents of the harmonic menu occupy a great amount of memory in the device, so no minimum / maximum values 

are stored for the harmonics. Single harmonics, as displayed in this menu, cannot be the source of alarms. Harmonic 

alarms should use the THD as source, which contains information of all harmonics of one source in one single value. 

4.5

 

Work 

This submenu contains the work accumulators. These accumulators count certain amounts of electrical energy given by 

the elapsed time of the powers. 

The work counters are programmed to integrate the powers for L1, L2, L3 and power sum in a separate accumulator 

each. They are further divided: 

 

Active work is accumulated separately for import and export energy flow direction 

 

Reactive work is accumulated separately for inductive and capacitive reactive power  

The display can show one of four different pages, which are: WP-IMP, WP-EXP, WQ-IND, WQ-CAP. Each page contains 

four work counters for L1, L2, L3 and sum(L1+L2+L3). For the counting of two tariffs, have devices with integrated data 

logger (option –DM) additional counters.  

These are also divided among four pages (WP-IMP-2, WP-EXP-2, WQ-IND-2 and WQ-KAP-2) and include also for counters 

for L1, L2, L3 and sum (L1+L2+L3). 

KEYS: 

 

Left key (“M”) switches back to main menu 

 

Right key (“

”) switches between the four different work accumulator pages 

Summary of Contents for EMM5























Reviews: