Belmont IO 5000TA Installation And Operation Instructions Manual Download Page 4

Intended Use of the Product

This product is intended for the exclusive use for diagnoses, treatments and relative procedures of dentistry, and must be operated 

or handled by the qualified dentists or by dental staffs under the supervision of the dentist.  Such dentists or dental staffs should 

instruct and/or assist the patients to approach to and leave from the product. Patients should not be allowed to operate or handle 
the product unless he/she is so instructed.

Important Notes
In case of the troubles, please contat Takara Belmont offices or your dealers. 

Do not disassemble or attempt to repair.

Disassembly, repair or modifications shoud only be done by a qualified repair technician. 
Attempts at disassembly, repair or modifications may lead to abnormal operation and accidents.

In case of disposal of equipment

When disposing the dental light, appropriately dispose complying with all current applicable regulations and local codes.  
In EU area, EU directive 2002/96/EC on waste electrical and electronic equipment (WEEE) is applied  on this product.  In this 
directive, environment conscious recycling/abandonment is obligated.

Environmental condition for Operation
  Temperature : 5 ~ 40℃ 

  Humidity : 10 ~ 80% 
  Pressure : 600 ~ 1060 hpa 

Environmental condition for Storage 
  Temperature : -10 ~ 50℃ 

  Humidity : 10 ~ 80% 
  Pressure : 600 ~ 1060 hpa 

Environmental condition for Transportation 
  Temperature : -10 ~ 50℃ 

  Humidity : 10 ~ 80% 
  Pressure : 600 ~ 1060 hpa

Symbols

㻨㻦

㻵㻨㻳

Non-ionizing

radiation

 Date of manufacture

Authorized 

representative in 

the European 

community

Manufacturer

Caution

It means “caution, 

warnings, or 

possibility to 

danger”.

Power ON

Power OFF

Alternating-current

Refer to instruction

manual/booklet

Separate 

collection for 

electrical and 

electronic 

equipment

Summary of Contents for IO 5000TA

























Reviews: