manualshive.com logo in svg

Belmont CP-ONE PLUS, Operating Instructions Manual, Page: 71 / 96

Share
Download
Belmont CP-ONE PLUS Operating Instructions Manual Download Page 71

 

 

Unit part 

67 

 

  Cuspidor unit 

 
 

 Water feed port adjustment knob 

(optional) 

▪  This knob adjusts the water feeding 

quantity from the spare water feed port.   

▪  The water quantity is decreased by 

turning the knob clockwise. It is 
increased by turning the knob 
counterclockwise.   

 
 
 
 

 Adjustment of the syringe spray 

▪  Use the syringe water quantity 

adjustment knob (blue cap) and syringe 
air quantity adjustment knob (yellow cap) 
for adjustment.   

▪  The flow rate is decreased by turning any 

knob clockwise. It is increased by turning 
the knob counterclockwise.   

 

 Cupfiller adjustment knob 

▪  This knob adjusts the water feeding 

quantity.   

▪  The flow rate is decreased by turning the 

knob clockwise. It is increased by turning 
the knob counterclockwise.   

*  Be sure to set the water feeding quantity, 

if the flow rate of feed water needs to be 
changed. See page 57 for setting of the 
water feeding quantity.   

 

 Bowl flush adjustment knob 

▪  This knob adjusts the flow rate of bowl 

rinse.   

▪  The flow rate is decreased by turning the 

knob clockwise. It is increased by turning 
the knob counterclockwise.   

 
 

NOTICE

 

Flow rate adjustment knobs for water and 
air are intended to increase/decrease the 
flow rate, but do not serve as stop valves. 
Caution should be exercised as turning 
the knob excessively may cause it to 
loosen.   

 
 

 

ADJUSTMENT OF PARTS 

Decrease 

Increase 

Summary of Contents for CP-ONE PLUS

































































































Reviews:

No comments