manualshive.com logo in svg

BELL LABS INNOVATIONS Lucent Technologies INTUITY MAP/5, Installation Manual, Page: 66 / 266

Share
Download
BELL LABS INNOVATIONS Lucent Technologies INTUITY MAP/5 Installation Manual Download Page 66

Connecting Peripherals and Powering Up

3-10

Issue  4.0   October 1996 

Setting Up a Terminal to Remotely Login to the
Lucent Intuity System via a 7400A Data Module

Use the documentation associated with your terminal and the following 
procedure.

1. Set the terminal line to 8 bits, no parity, and 1 stop bit.

2. Set the terminal line speed the same as the speed of the data module the 

terminal is connected to.

Connecting the 3820 Modem

The Lucent Technologies Paradyne 3820 modem is supported for connection to 
COM2 (Serial Port 2). COM2 (Serial Port 2) is reserved for Lucent Technologies 
remote maintenance on all systems except those integrated with MERLIN 
LEGEND. Alarm Origination is optional on MERLIN LEGEND integrations.

Follow the sections below to install the 3820.

Physically Connecting the 3820 Modem

To physically connect the 3820 modem to the hardware platform, follow the steps 
below:

1. Connect a 9-25 pin adapter to the 9 pin COM2 (Serial Port 2) on the back 

of the MAP/5.

2. Use a 25-8 pin adapter to complete the connection between the 9-pin 

COM2 (Serial Port 2) and the 8-pin modular cable that comes with the 
3820 modem; connect the 9-25 pin adapter to the 25-8 pin adapter and 
then connect the 25-8 pin adapter to the 8-pin modular cable. 

3. Plug the 8-pin modular cable into the 3820 modem 

You have completed this procedure.

Once connected, RTS, CTS, and LSD on the 3820 modem should be on when 
you power up the MAP/5. 

If using the modem for anything other than Lucent Technologies remote 
maintenance, use the RS-232 (M25B) adapter marked as DTE and the six-pin 
cable to connect to the ports (ttysaa, etc.) on the multi-port serial card and the 
3820 modem.

Summary of Contents for Lucent Technologies INTUITY MAP/5











































































































































































































































































Reviews:

No comments