manualshive.com logo in svg

BELL LABS INNOVATIONS Lucent Technologies INTUITY MAP/5, Installation Manual, Page: 2 / 266

Share
Download
BELL LABS INNOVATIONS Lucent Technologies INTUITY MAP/5 Installation Manual Download Page 2

Copyright 

 1996, Lucent Technologies

All Rights Reserved
Printed in U.S.A.

Notice
Every effort was made to ensure that the information in this book was 
complete and accurate at the time of printing.  However, information 
is subject to change.

Your Responsibility for Your System’s Security
Toll fraud is the unauthorized use of your telecommunications system 
by an unauthorized party, for example, persons other than your com-
pany’s employees, agents, subcontractors, or persons working on your 
company’s behalf. Note that there may be a risk of toll fraud associ-
ated with your telecommunications system and, if toll fraud occurs, it 
can result in substantial additional charges for your telecommunica-
tions services.

You and your system manager are responsible for the security of your 
system, such as programming and configuring your equipment to pre-
vent unauthorized use.  The system manager is also responsible for 
reading all installation, instruction, and system administration docu-
ments provided with this product in order to fully understand the fea-
tures that can introduce risk of toll fraud and the steps that can be 
taken to reduce that risk. Lucent Technologies does not warrant that 
this product is immune from or will prevent unauthorized use of com-
mon-carrier telecommunication services or facilities accessed through 
or connected to it.  Lucent Technologies will not be responsible for 
any charges that result from such unauthorized use.

Lucent Technologies Fraud Intervention
If you suspect that you are being victimized by toll fraud and you need 
technical support or assistance, call Technical Service Center Toll 
Fraud Intervention Hotline at 1 800 643-2353.

Federal Communications Commission Statement
Part 15: Class A Statement. This equipment has been tested and 
found to comply with the limits for a Class A digital device, pursuant 
to Part 15 of the FCC Rules.  These limits are designed to provide rea-
sonable protection against harmful interference when the equipment is 
operated in a commercial environment.  This equipment generates, 
uses, and can radiate radio-frequency energy and, if not installed and 
used in accordance with the instructions, may cause harmful interfer-
ence to radio communications.  Operation of this equipment in a resi-
dential area is likely to cause harmful interference, in which case the 
user will be required to correct the interference at his own expense.

Part 68: Network Registration Number. This equipment is regis-
tered with the FCC in accordance with Part  68 of the FCC Rules. It is 
identified by FCC registration number AS5USA-20411-VM-E.

Part 68: Answer-Supervision Signaling. Allowing this equipment to 
be operated in a manner that does not provide proper answer-supervi-
sion signaling is in violation of Part 68 Rules. This equipment returns 
answer-supervision signals to the public switched network when:

•

Answered by the called station

•

Answered by the attendant

•

Routed to a recorded announcement that can be administered 
by the CPE user

This equipment returns answer-supervision signals on all DID calls 
forwarded back to the public switched telephone network.  Permissi-
ble exceptions are: 

•

A call is unanswered

•

A busy tone is received

•

A reorder tone is received

Canadian Department of Communications (DOC)
Interference Information
This digital apparatus does not exceed the Class A limits for radio 
noise emissions set out in the radio interference regulations of the 
Canadian Department of Communications.

Le Présent Appareil Nomérique n’émet pas de bruits radioélectriques 
dépassant les limites applicables aux appareils numériques de la class 
A préscrites dans le reglement sur le brouillage radioélectrique édicté 
par le ministére des Communications du Canada.

Trademarks
See the About This Document section of this book.

Ordering Information
Call:

Lucent Technologies Publications  Center
Voice 1 800 457-1235

International Voice 317 361-5353

Fax 1 800 457-1764

International Fax 317 361-5355

Write:

Lucent Technologies Publications Center
P.O. Box 4100
Crawfordsville, IN 47933

Order:

Document No.  585-310-146
Comcode 107856882
Issue 4, October 1996

For additional documents, refer to the section in “About This Docu-
ment” entitled “Related Resources.” 

You can be placed on a standing order list for this and other documents 
you may need. Standing order will enable you to automatically receive 
updated versions, billed to account information that you provide. For 
more information or to be put on a list to receive future issues of this 
document, contact the Lucent Technologies Publications Center.

European Union Declaration of Conformity
Lucent Technologies  Business Communications Systems declares 
that MAP/40 and MAP/100 equipment specified in this document con-
forms to the referenced European Union (EU) Directives and Harmo-
nized Standards listed below:
EMC Directive

89/336/EEC

Low-Voltage Directive

73/23/EEC
The “CE” mark affixed to the equipment 
means that it conforms to the above 
directives.

Disclaimer
Intellectual property related to this product and registered to AT&T 
Corporation has been transferred to Lucent Technologies Incorpo-
rated.

Any references within this text to American Telephone and Telegraph 
Corporation or AT&T should be interpreted as references to Lucent 
Technologies Incorporated. The exception is cross references to books 
published prior to December 31, 1996, which retain their original 
AT&T titles.

Heritage
Lucent Technologies - formed as a result of AT&T’s planned restruc-
turing - designs, builds, and delivers a wide range of public and private 
networks, communication systems and software, consumer and busi-
ness telephone systems, and microelectronics components. The world-
renowned Bell Laboratories is the research and development arm for 
the company.

This document was prepared by the Product Documentation Develop-
ment, Lucent Technologies, Columbus, OH.

Summary of Contents for Lucent Technologies INTUITY MAP/5











































































































































































































































































Reviews:

No comments