Beltis Fire Pit Kit
Beltis Fire Pit
Earth Blend
Get Social
©2018 Oldcastle. All Rights Reserved. BEL18-EXPO-BELTISFIREPIT
Facebook.com/BelgardHardscapes
Belgard.com/Enews
Belgard.com/Blog
Twitter.com/Belgard
YouTube.com/BelgardHardscapes
Pinterest.com/Belgard
British Columbia Alberta Saskatchewan Manitoba
For more info visit: Belgard.com | Expocrete.com
Colours:
Shadow Blend
Earth Blend
Installation Information
•
Time to Complete - Approximately 1 hour
•
Degree of Difficulty - Beginner
Additional Materials Required
•
Tamper
•
Household Level
•
2 Bags of Leveling Sand
•
2 Tubes of Concrete Adhesive
•
Caulk Gun
•
3 Bags of Gravel Rock
•
Shovel
•
Optional Marking Paint or Chalk
Please ensure you follow all local bylaws regarding
fire pits, their installation, placement and usage in
your community.
Always observe open fire and fire pit safety rules.
Expocrete, a division of Oldcastle Building Products
Canada, Inc. accepts no liability for the use of any
fire pit built with our materials.
For a lawn, mark a 49” diameter circle
with marking paint then go to step 2.
For a patio, use chalk instead of paint
then skip to step 5.
Add 1.5”-2” of paver base and level.
Moisten with water to aid compaction
then use a tamper to pack the entire
area firm. Add .5”-1” more of paver
base and level again.
Attach the two layers of stone together
using concrete adhesive. Remove one top
stone and lay 2 liberal beads of adhesive
near the center of the stone. Place stone
back and press down firmly. Repeat for
all 2nd layer stones.
Lay the third layer the same way you
laid the second. The third layer joints
should line up with the first layer joints.
Adhere the stones with concrete
adhesive as you did in step 7.
After all stones are set, install the fire pit
insert. The insert’s top lip should rest on
the inside edge of the fire pit stones.
After the adhesive cures, pour gravel rock
into the bottom of the fire pit, leveling it
as you go. The gravel should reach the
bottom of the insert ring.
Remove all sod, roots and dirt to a depth
of 2 inches inside the circle.
Place wall stones on top of paver base,
firmly touching each stone creating a
circle. Make sure each stone is leveled
front to back and side to side and even
with adjacent stones.
For the second layer of stone, lay the
middle of each stone over the joint made
between the sides of the two stones
underneath it. Place stones firmly together
and level as before.
Level the soil and remove high spots
as best possible. Tip: Use a household
level to help.
STEP
1
FIRE PIT KIT
©2017 Expocrete. All Rights Reser
ved. L
WS12- 0007
Beltis Wall
• 36* Beltis Wall Blocks
• 7 Gauge Heavy-Duty Steel Insert
Includes:
• Tamper
• Household Level
• 2 Bags of Leveling Sand
• 2 Tubes of Concrete Adhesive
• Caulk Gun
• 3 Bags of Gravel Rock
• Shovel
• Optional Marking Paint or Chalk
Additional Materials Needed:
Instructions
Time to Complete
Degree of Difficulty
1 hr
Beginner
Fire pit requires 36 blocks- your
kit may include additional blocks
that are not required to complete
your fire pit.
*
STEP
2
STEP
3
STEP
4
STEP
7
STEP
10
STEP
8
STEP
9
STEP
5
STEP
6
Please ensure you follow all local bylaws regarding fire pits, their installation,
placement and usage in your community.
Always observe open fire and fire pit safety rules. Expocrete, a division of
Oldcastle Building Products Canada, Inc. accepts no liability for the use of
any fire pit built with our materials.
Installation:
