manualshive.com logo in svg

Belden 934 840 001, Technical Manual, Page: 103 / 105

Share
Download
Belden 934 840 001 Technical Manual Download Page 103

Accessories

Technical manual  LioN-P PROFINET IO-Link Master

Release 2.0 04/2017

103

12 Accessories

Item number

Description

0985 706 100/… M

Connection cable for Ethernet interface, assembled with M12 
connector at both ends, straight, 4-pin, D-coded, 24AWG TPE with 
blue-green shield, highly flexible, multi-wire/unshielded, 2 twisted wire 
pairs.

0985 706 101/… M

Connection cable for Ethernet interface, crossover, with M12 
connector at both ends, straight, 4-pin, D-coded, 24AWG TPE with 
blue-green shield, highly flexible, multi-wire/unshielded, 2 twisted wire 
pairs.

0985 706 103/… M

Connection cable for Ethernet interface, with M12 connector at both 
ends, straight, 4-pin, D-coded and RJ45 connector, 24AWG TPE with 
blue-green shield, highly flexible, multi-wire/unshielded, 2 twisted wire 
pairs.

0985 707 100/… M

Connection cable for Ethernet interface, with M12 connector at both 
ends, straight, 4-pin, D-coded, 24AWG PVC with blue-green shield, 
flexible, solid conductor/unshielded, 2 twisted wire pairs.

0985 707 101/… M

Connection cable for Ethernet interface, crossover, with M12 
connector at both ends, straight, 4-pin, D-coded, 24AWG PVC with 
blue-green shield, flexible, solid conductor/unshielded, 2 twisted wire 
pairs.

0985 S4549 100/… M Connection cable for Ethernet interface, with M12 connector at both 

ends, straight, 4-pin, D-coded, 26AWG PUR, halogen-free, with water-
blue shield, multi-wire/shielded, 2 twisted wire pairs.

0985 S4549 103/… M Connection cable for Ethernet interface, with M12 connector at both 

ends, straight, 4-pin, D-coded and RJ45 connector, 26AWG PUR, 
halogen-free, with water-blue shield, multi-wire/shielded, 2 twisted 
wire pairs.

0985 342 100/... M

Connection cable, M12-M12, Industrial Ethernet data line as per 
PROFINET type C, overmolded on both sides with M12 connectors, D-
coded as per IEC 61076-2-101, 4-pin, PUR shield, halogen free, 
shielded, green

0985 342 102/... M

Connection cable for PROFINET, assembled on one side with an M12 
connector, 4-pin, D-coded

0985 342 104/... M

Connection cable as per PROFINET type C, assembled on one side 
with an M12 connector, 4-pin, D-coded and RJ45 connector

Table 52: Connection cables for data transfer

Item number

Description

0986 EMC 102

M12 cable connector for PROFINET   IO cable, straight, 4-pin, D-
coded, connection for spring terminal

Table 53: Customizable connectors for data transfer

Summary of Contents for 934 840 001










































































































Reviews:

No comments