BEL Engineering HPBG Series User Manual Download Page 22

Page: 22 / 74

10.1 Weight Units

The scale can be set to display the weight in the different units, one primary (

Weight Units 1

)

and one secondary (

Weight Units 2

When we supply the scale, the default unit of measurement is

Weight Units 1

1. From display zero condition press and keep pressed the

MENU

button until the

acoustic alarm gets mute, then release the button. The setup menu will be displayed
then select

“

Weight Units 1

” and press

PRINT

to confirm.

It will be displayed “

Grams

” unit. Pressing the

MENU

CAL

button, it will be possible

to scroll forward or backward the weight units menu.

3. Press

PRINT

button to confirm or

MENU

button to shift to the other weight unit.

SYMBOL

UNIT

CONVERSION

FACTOR 1g =

GrAM

GRAM

MiLLi Gr

MILLIGRAMMES

0.001

CArAt

CARAT

OuncE

ONCE

0.035273962

Pound

POUND

0.0022046226

PEnn.

PENNYWEIGHTS

0.643014931

OuncETr.

ONCE TROY

0.032150747

GrA in

GRAIN

15.43235835

tAEL Hon

HONG KONG

TAEL

0.02671725

tAEL SGP

SYNGAPORE

TAEL

0.02646063

tAEL roc

R.O.C. TAEL

0.02666666

MoMME

MOMME

0.2667

2 Sec

Setup Menù

Weight Units 1

- Serial output
- Baud rate
- Auto zero

Weight Units 2

Grams

Weight Units 1

Summary of Contents for HPBG Series











































































Search results

Summary of Contents for HPBG Series

Reviews:

Brands by name

Popular brands

BEL Engineering HPBG Series, User Manual

Search results

Summary of Contents for HPBG Series

Reviews:

Brands by name

Popular brands