5 / EN
Washing Machine / User’s Manual
Remove the transportation safety bolts before operating the
washing machine! Otherwise, the product will be damaged.
Loosen all the bolts with a suitable spanner until they rotate
freely (C). Remove transportation safety bolts by turning them
gently. Attach the plastic covers supplied in the User Manual
bag into the holes on the rear panel. (P)
C
INFORMATIONS
Keep the transportation safety bolts in a safe place to reuse when
the washing machine needs to be moved again in the future.
Never move the product without the transportation safety bolts
properly fixed in place!
2.4 Connecting water supply
C
INFORMATIONS
The water supply pressure required to run the product is between
1 to 10 bars (0.1 – 1 MPa). It is necessary to have 10 – 80 liters
of water flowing from the fully open tap in one minute to have your
machine run smoothly. Attach a pressure reducing valve if water
pressure is higher.
If you are going to use the double water-inlet product as a single
(cold) water-inlet unit, you must install the supplied stopper to
the hot water valve before operating the product. (Applies for the
products supplied with a blind stopper group.)
If you want to use both water inlets of the product, connect the
hot water hose after removing the stopper and gasket group from
the hot water valve. (Applies for the products supplied with a blind
stopper group.)
A
WARNING
Models with a single water inlet should not be connected to the
hot water tap. In such a case the laundry will get damaged or the
product will switch to protection mode and will not operate.
Do not use old or used water inlet hoses on the new product. It may
cause stains on your laundry.
Connect the special hoses supplied with the product to the
water inlets on the product. Red hose (left) (max. 90 ºC) is for
hot water inlet, blue hose (right) (max. 25 ºC) is for cold water
inlet.
A
WARNING
Ensure that the cold and hot water connections are made correctly
when installing the product. Otherwise, your laundry will come out
hot at the end of the washing process and wear out.
Tighten all hose nuts by hand. Never use a wrench when
tightening the nuts. Open the taps completely after making the
hose connection to check for water leaks at the connection
points. If any leaks occur, turn off the tap and remove the nut.
Retighten the nut carefully after checking the seal. To prevent
water leakages and damages caused by them, keep the taps
closed when the machine is not in use.
2.5 Connecting to the drain
• The end of the drain hose must be directly connected to
the wastewater drain or to the washbasin.
A
WARNING
Do not remove the transportation locks before taking out the
packaging reinforcement.
• The hose should be attached to a height of at least 40 cm,
and 100 cm at most.
• In case the hose is elevated after laying it on the floor level
or close to the ground (less than 40 cm above the ground),
water discharge becomes more difficult and the laundry
may come out excessively wet. Therefore, follow the
heights described in the figure.
100cm
40cm
• To prevent flowing of dirty water back into the machine and
to allow for easy discharge, do not immerse the hose end
into the dirty water or do not drive it in the drain more than
15 cm. If it is too long, cut it short.
• The end of the hose should not be bent, it should not be
stepped on and the hose must not be pinched between the
drain and the machine.
• If the length of the hose is too short, use it by adding
an original extension hose. Length of the hose may not
be longer than 3.2 m. To avoid water leak failures, the
connection between the extension hose and the drain
hose of the product must be fitted well with an appropriate
clamp as not to come off and leak.
2.6 Adjusting the feet
A
WARNING
In order to ensure that the product operates more silently and
vibration-free, it must stand level and balanced on its feet. Balance
the machine by adjusting the feet. Otherwise, the product may
move from its place and cause crushing and vibration problems.
Loosen the lock nuts on the feet by hand. Adjust the feet until
the product stands level and balanced. Tighten all lock nuts
again by hand.
A
WARNING
Do not use any tools to loosen the lock nuts. Otherwise, they will
get damaged.
2.7 Electrical connection
Connect the product to a grounded outlet protected by a fuse
complying with the values in the "Technical specifications"
Summary of Contents for WMB 51001 Y+
