background image

7/EN

hose set. Do not make extension 

at the hoses.

NOTICE 

Connect the water inlet 

hose directly to the water tap. 

Pressure coming from the tap 

should be 0.03 MPa (0.3 bars) 

minimum and 1MPa (10 bars) 

maximum. If the water pressure 

exceeds 1 MPa (10 Bars), a 

pressure relief valve should be 

installed in between.

 Route the power cable and 

hoses in a way that they do 

not cause risk of tripping. 

Operational safety

 

Only dishwasher safe 

detergents, rinse aids and 

additives must be used.

 Never use chemical solvents 

in the product. They bring 

forth the risk of explosion.

 The wash-water inside the 

product is not potable.

 Dishwasher detergents have 

high alkali content and can 

be very dangerous when 

ingested. Avoid letting them 

get into contact with skin and 

eyes and keep children away 

from the product when its 

door is open. Make sure that 

the detergent dispenser is 

empty after the washing cycle 

is complete.

 When you pull the upper and 

lower baskets out completely, 

the door of the product will 

bear all the weight of the 

baskets. Do not sit or put 

other loads on the door; 

otherwise, the product may 

tilt.

 Maximum washing capacity 

of the product is stated in the 

section called 

“Technical 

Specifications”

.

 To prevent possible injuries, 

always place the sharp and 

pointed dishes such as 

service fork, bread knife, 

etc. upside down so as their 

pointed ends face down or 

they lie horizontally in the dish 

basket.

 Open the door of the product 

carefully if you need to do so 

when the product is running. 

Be careful against hot steam 

that may escape or hot water 

that may spill.

 Do not start the broken or 

damaged product. Unplug 

the product (or switch off the 

fuse it is connected to), turn 

off the water tap and call the 

authorised service agent.

 Do not place flame sources 

(lit candles, cigarettes, etc.) 

on or close to the product. 

Do not keep combustable/

flammable substances close 

to the product.

 Do not climb on the product.

 

Unplug the product and close 

the tap if you are not going to 

use it for a long time. 

Summary of Contents for Hygiene Shield BDEN38520H

















































Reviews: