Beko EV 5100 +Y, User Manual

Page: 12 / 68

12 / 68 EN
Washing Machine / User’s Manual
5.3 Cleaning the body and control panel
Wipe the body of the machine with soapy water or non-
corrosive mild gel detergents as necessary, and dry with a
soft cloth.
Use only a soft and damp cloth to clean the control panel.
A
WARNING
Never use sponge or scrub materials. These will damage the
painted and plastic surfaces.
5.4 Cleaning the water intake filters
There is a filter at the end of each water intake valve at the
rear of the machine and also at the end of each water intake
hose where they are connected to the tap. These filters
prevent foreign substances and dirt in the water to enter the
washing machine. Filters should be cleaned as they do get
dirty.
Close the taps. Remove the nuts of the water intake hoses
to access the filters on the water intake valves. Clean them
with an appropriate brush. If the filters are too dirty, take them
out by means of pliers and clean them. Take out the filters
on the flat ends of the water intake hoses together with the
gaskets and clean thoroughly under running water. Replace
the gaskets and filters carefully in their places and tighten the
hose nuts by hand.
5.5 Draining remaining water and
cleaning the pump filter
The filter system in your machine prevents solid items such
as buttons, coins and fabric fibers clogging the pump impeller
during discharge of washing water. Thus, the water will be
discharged without any problem and the service life of the
pump will extend.
If the machine fails to drain water, the pump filter is clogged.
Filter must be cleaned whenever it is clogged or in every 3
months. Water must be drained off first to clean the pump
filter.
In addition, prior to transporting the machine (e.g., when
moving to another house) and in case of freezing of the water,
water may have to be drained completely.
A
WARNING
Foreign substances left in the pump filter may damage your
machine or may cause noise problem.
In order to clean the dirty filter and discharge the water:
Unplug the machine to cut off the supply power.
A
WARNING
Temperature of the water inside the machine may rise up to 90 ºC.
To avoid burning risk, filter must be cleaned after the water in the
machine cools down.
5 Maintenance and cleaning
Service life of the product extends and frequently faced
problems decrease if cleaned at regular intervals.
5.1 Cleaning the detergent drawer
Clean the detergent drawer at regular intervals (every
4-5 washing cycles) as shown below in order to prevent
accumulation of powder detergent in time.
Press the dotted point on the siphon in the softener
compartment and pull towards you until the compartment is
removed from the machine.
C
INFORMATIONS
If more than normal amount of water and softener mixture starts to
gather in the softener compartment, the siphon must be cleaned.
Wash the detergent drawer and the siphon with plenty of
lukewarm water in a washbasin. Wear protective gloves or use
an appropriate brush to avoid touching of the residues in the
drawer with your skin when cleaning. Insert the drawer back
into its place after cleaning and make sure that it is seated
well.
5.2 Cleaning the loading door and the drum
Residues of softener, detergent and dirt may accumulate in
your machine in time and may cause unpleasant odours and
washing complaints. To avoid this, use the Drum Cleaning
programme. If your machine does not have a Drum Cleaning
programme, use Cotton-90 programme. Before starting the
programme, put max. 100 g of powder anti-limescale into
the main wash detergent compartment (compartment nr. II).
If the anti-limescale is in tablet form, put only one tablet into
compartment nr. II. Dry the inside of the bellow with a clean
piece of cloth after the programme has come to an end.
C
INFORMATIONS
Repeat Drum Cleaning process in every 2 months.
Use an anti-limescale suitable for the washing machines.
After every washing make sure that no foreign substance is
left in the drum.
If the holes on the bellow shown in the figure is blocked, open
the holes using a toothpick.
C
INFORMATIONS
Foreign metal substances will cause rust stains in the drum.
Clean the stains on the drum surface by using cleaning agents for
stainless steel. Never use steel wool or wire wool.