Beko DRYPOINT RS 100-E HP50 NA, Instructions For Installation And Operation Manual

Page: 30 / 72

Technical description
30 DRYPOINT® RS 15-550 HP50 NA
11.19.5 How is controlled the condenser fan
A pressure probe BP2 is located on the discharge side of the compressor. The condenser fan is activated (ON) when
the BP2 pressure is higher than FANon setting (R134a approx. 11 barg/160 psig
– R407C approx. 18 barg/260 psig) and
led is ON. Condenser fan stops when BP2 pressure is lower than FANoff setting (R134a approx. 8 barg/115 psig
– R407C approx. 14 barg/203 psig).
11.19.6 How is controlled the drain solenoid valve
Drain solenoid valve is activated (ON) for seconds (standard 2 seconds) every minutes (standard 1 minute).
Led shows that condensate drain solenoid valve is ON.
The condensate drain test is always active using the button .
NOTE : if an electronic drainer is installed, DMC34 is set to keep always powered the drain output ( = ON).
11.19.7 How to reset the service reminder timer
With dryer OFF keep pressed buttons + , power the dryer and switch it on using the ON-OFF
switch (pos.1 paragraph 7.1).
After 5 seconds display shows , release buttons + , keep pressed button for 5
seconds. Timer has been reset and controller start to operate regularly.
Service reminder timing can be reset at any time, even before the timing has expired.
11.19.8 Operation of the failure / alarm dry contact
The DMC34 is equipped with a dry contact (potential free) to display failure and/or alarm conditions.
Dryer powered and no service warning / alarm is active.
Dryer not powered or service warning / alarm is active.
11.19.9 How to change the operating parameters
The setup menu can be used to
change the dryer’s operating parameters.
Only qualified personnel must be allowed to access to the setup menu. The manufacturer is not
responsible for malfunctioning or failure due to modification to the operating parameters.
With dryer ON simultaneously press buttons + for at least 5 seconds to enter the setup menu.
Access to the menu is confirmed by message on the display (first parameter of menu).
Keep pressed to display the value of the selected parameter and use arrows and to
change the value. Release the button to confirm the value and skip to following parameter.
Press + to exit setup menu (if no button is pressed after 2 minutes the menu is exited
automatically).
ID Description Limits Resolution
Standard
setup
Ton
– drain time ON : time ON condensate drain valve
ON = Electronic drainer installed
ON
00 … 20 sec
1 sec 2
ToF - drain time OFF : pause time for condensate drain valve
1 … 20 min
1 min 1
HdS
– High DewPoint Setting : Alarm threshold for a high
DewPoint (the alarm disappears when the temperature drop
1°C / 2°F below alarm point)
0.0…25.0 °C
or
32 … 77 °F
0.5 °C
or
1 °F
20
or
68
Hdd - High DewPoint Delay : high DewPoint alarm enable
delay
01 … 20
minutes
1 min 15
SrV - Service Setting: setting of service warning timer.
00 = service warning timer disabled. 00.0
… 20.0
(x 1000) hours
0.5
(x1000)
hours
08.0
SrC
– Service Contact : configuration of the alarm dry contact
for the service warning timer.
YES = activate the contact / NO = NOT activate the contact YES / NO - YES
SCL - Scale: display scale of temperatures and pressure (°C
= temperatures in °C and pressure in barg; °F = temperatures
in °F and pressure in psig)
°C … °F
- °C
Set
Set
8 9
8 9
Set
Set
Set