background image

 

Declaration of conformity

 

BEKOMAT® 31U IF built-in F 

21

 

 

BEKO 

TECHNOLOGIES GMBH 

Im Taubental 7 
41468 Neuss 
 
GERMANY 
 
Phone: +49 2131 988-0 
www.beko-technologies.com  

 

EU Declaration of Conformity  

 

We hereby declare that the products named below comply with the stipulations of the relevant directives and 
technical standards. This declaration only refers to products in the condition in which they have been placed 
into circulation. Parts which have not been installed by the manufacturer and/or modifications which have 
been implemented subsequently remain unconsidered. 
 
Product designation: 

Condensate drain 

Type: 

BEKOMAT

®

 31UIF, 32UIF, 32UVIF, 33UIF 

Supply voltage versions: 

24 VDC ±10% 

Maximum operating pressure: 

16 bar (g) 

Product description and function: 

Condensate drain off for the electronically level-controlled 
discharge of condensate in the refrigeration dryer. 

 

EMC Directive 2014/30/EU 

Applied harmonised standards: 

EN 61326-1:2013 

 

RoHS II Directive 2011/65/EU 

The products meet the requirements laid down in European Directive 2011/65/EU concerning the restriction 
of the use of certain hazardous substances in electrical and electronic devices. 

 
The manufacturer shall have sole responsibility for issuing this declaration of conformity.  
 

Signed for and on behalf of:  

 
Neuss, 04 August 2016

 

BEKO 

TECHNOLOGIES GMBH 

 
 
 

i.V. Christian Riedel 

 

Head of International Quality Management 

 

 

 

 

 
 

Summary of Contents for BEKOMAT 31U IF built-in F

























Reviews: