Beko BEKOMAT 16 CO Original Installation And Operation Manual Download Page 13

Page: 13 / 60

3.4 Type plate

The type plate is located on the housing and contains all the identification and operating parameters of the

BEKOMAT

If you contact the manufacturer or supplier, always have this data ready for system identification.

Position on type plate

Description / explanation

BM16CO

Product name

0.8 … 16 bar / 12 … 230 psig

Operating pressure

+1° … +60 °C / 34° … 140 °F

Operating temperature

230 Vac ± 10% /50-60Hz/ <8VA

Operating voltage

2000787

Order reference

14266245

Serial number

IP65

IP degree of protection

NOTE

Handling the type plate!

Never damage, remove or make the type plate illegible.

For more information regarding the symbols, refer to

“2.4 Explanation of the symbols used” on Page 8.

3.5 Scope of delivery

The table below shows the scope of delivery of the

BEKOMAT

Illustration

Description / explanation

BEKOMAT

Original installation and operation manual

BEKO TECHNOLOGIES GmbH

14136065

BM16CO

0,8 ... 16 bar / 12 ... 230 psig

+1° ... + 60 °C / 34° ... 140 °F

230 Vac ± 10% /50 ... 60Hz/ <8VA

Made in Germany

2000787

14266245

IP65

BEKO TECHNOLOGIES GmbH

14136065

BM16CO

0,8 ... 16 bar / 12 ... 230 psig

+1° ... + 60 °C / 34° ... 140 °F

230 Vac ± 10% /50 ... 60Hz/ <8VA

Made in Germany

2000787

14266245

IP65

Example illustrations

Original installation and operation manual

BEKOMAT

16 CO

13 | 60

Summary of Contents for BEKOMAT 16 CO





























































Search results

Summary of Contents for BEKOMAT 16 CO

Reviews:

Related manuals for BEKOMAT 16 CO

Brands by name

Popular brands

Beko BEKOMAT 16 CO, Original Installation And Operation Manual

Search results

Summary of Contents for BEKOMAT 16 CO

Reviews:

Related manuals for BEKOMAT 16 CO

Brands by name

Popular brands