manualshive.com logo in svg

Beko Bekomat 14, Original Installation And Operation Manual, Page: 44 / 64

Share
Download
Beko Bekomat 14 Original Installation And Operation Manual Download Page 44

10.3.2  Cleaning work

Clean the 

BEKOMAT

®

 using a damp (not dripping wet) cotton cloth or disposable wipe, a cleaning brush and a mild, 

conventional cleaning agent/soap.
Spray the cleaning agent on a clean cotton cloth or disposable wipe and wipe down the entire component. Then dry 

using a clean cloth or let it dry at room temperature.

Carry out the individual cleaning steps as follows:

Illustration

Description / explanation

1.  Clean the control-air bore and condensate discharge 

bore using a cleaning brush Ø max. = 2.5 mm (0.09").

2.  Clean the control-air cover using a cleaning brush 

Ø max. = 2.5 mm (0.09").

3.  Clean the upper opening on the core guide pipe using 

a cleaning brush Ø max. = 2.5 mm (0.09").

4.  Clean the core guide pipe from below using a cleaning 

brush or a clean cloth.

BEKOMAT

®

 13, 13 CO, 13 CO PN25, 13 CO PN40

Original installation and operation manual

44 | 64

Summary of Contents for Bekomat 14

































































Reviews:

No comments