background image

8/EN

Technical specifications

Maximum washing capacity (check the 

energy label and Programme data and 

average consumption values table given 

on Quick Guide. )

Height (check installation document for 

installation)
Width: 60 
Depth:  57

Power input:  220-240 V, 

50

 Hz *

Total power 1800-2100  W *
Heater power: 1800 W *
Total current: 10 A *
Pump power: 90 - 125 W *
Drain pump power: 30 W *
* For detailed electrical values, check 

the type label on the machine door.

Water Pressure 0.3 –10 bar

 (= 3 – 100 N/cm² = 0.03-1.0 Mpa)

 Technical specifications may be 

changed without prior notice to improve 

the quality of the product.

 Figures in this manual are schematic 

and may not match the product exactly.

 Values stated on the markings of the 

product or in the printed documents 

accompanying the product are 

obtained in the laboratory on basis of 

the relevant standards. These values 

may vary according to the usage of the 

product and ambient conditions.

Note for test institutions:

Data required for performance tests shall 

be provided upon request. Requests can 

be e-mailed to the following address:

[email protected]

Do not forget to provide the code, stock 

number and serial number of the product 

to be tested in your request e-mail along 

with your contact information. Code, stock 

number and serial number of the product 

may be found on the type label attached to 

the side wall of the door.

Compliance to standards and test 

data/EC declaration of conformity

Development, production and 

sales stages of this product comply 

with the safety rules included in all 

pertaining European Community 

regulations.

2014/35/EU, 2014/30/EU, 93/68/EC, IEC 

60436 / EN 60436

 The model information as stored in 

the product database can be reached 

by entering following website and 

searching your model identifier (*) 

found on energy label.

https://eprel.ec.europa.eu/

XXXXXXXXXX (*)

18 7575 8000

3:25

REV:AA

12.9 L

94

13

x

kWh

2019

/2017

48

db

Summary of Contents for BDDN38530DD













































Reviews: