BEINAT BX280-AX Manual Download Page 4 | Manualshive

Page: 4 / 16

BEINAT BX280-AX Manual Download Page 4

{a} OVERVIEW

-  Power  supply  110/240  VAC
-  Controls  up  to  2  remote  sensors
-  Manages  explosive  and  toxic  gases.
-  Various  possibilities  of  configuration  parameters
-  Status  indications  with  LED.
-  Output  signals  provided  through  3  driving  relays
-  wall  support  6  DIN  modules.
-  Conforms  to  the  operating  regulations  EN60079-29-1

{b} GENERAL DESCRIPTION

The  BX280-AX  is  a  control  unit  capable  to  control  the  concentration  of  gas  up  to  2  input  channels,  each  of
which  can  be  connected  via  a  4-20  mA  communication  to  a  toxic  or  explosive  gas  detection/measurement
device.  The  control  unit  is  built  with  the  following  I/O  interfaces.

1)  RED  LED.
When  it  is  on,  the LED  flashes for  the  first 100  seconds,  which indicates  that  the control  unit  is  in  the warm  up
mode.  After  this  phase,  the  control  unit  enters  detection  mode.
When  this  LED  is  blinking,  the  BX280-AX  is  not  able  to  detect  gas.

2)  BATTERY  LED.
This  LED  lights  up  when  the  BX280-AX  is  powered  by  the  battery  in  the  absence  of  mains  and  flashes  when
the  battery  voltage  is  less  than  10.8  V.

3)  LED  SCALE  CONCENTRATION  GAS.
These  LEDs  light  up  in  sequence,  based  on  the  increase  to  the  gas  dispersed  in  the  environment.
a)  When  the  first  led  turns  on,  the  gas  concentration  level  has  reached  the  first  pre-alarm  threshold
b)  When  the  second  led  turns  on,  the  gas  concentration  level  has  reached  the  second  pre-alarm  threshold
c)  When  the  third  led  turns  on,  the  gas  concentration  level  has  reached  the  main  alarm  threshold
This  LED  is  the  "latching"  type,  it  stays  on  to  indicate  the  alarm  presence  stored  in  MEMORY,  according  to  the
current  operating  regulations

LED  OVERLOAD
4)  The  control  unit  is  equipped  with  electronic  OVERLOAD  protections,  to  avoid  irreparable  damage.
LED  OVERLOAD  SENSOR
This  LED  lights  up  when  there  is  a  short  circuit  or  excessive  absorption  in  the  power  supply.
LED  OVERLOAD  BATTERY
This  LED  lights  up  when  there  is  a  short  circuit  or  excessive  absorption  in  the  backup  battery  supply

Control Unit from 1 to 2 Conventional sensors BX280-AX

page 4

Instruction manual

1 0

1 1

9

9

5

6

1 4

1 3

3

1

4

2

8

7

1 2

«
...
2
3
4
5
6
...
»

Summary of Contents for BX280-AX

















Reviews:

No comments