background image

JetNet 6728G Series Industrial 28G Full Gigabit Managed PoE Plus Ethernet Switch

Quick Installation Guide V1.0

The JetNet 6728G Series is a 19-inch Industrial 28G Full Gigabit Managed PoE Plus Ethernet 
Switch equipped 24 100/1000Base-TX with 24/16 PoE Plus ports, 4 Gigabit SFP ports.  

Dimension

JetNet 6728G Industrial 28G Full Gigabit Managed PoE Plus Ethernet Switch dimension 
(W x H x D) is 44mm(H) x 440mm (W) x 378.5mm (D). 

Front-Panel Components

The front panel includes RJ-45 based RS-232 console port, USB port, System & port LEDs, 
Gigabit Ethernet port Interfaces and Gigabit combo port Interfaces.

LED Indicators

Back-Panel Components

The back panel of the JetNet 6728G Industrial 28G Full Gigabit Managed PoE Plus Ethernet 
Switch consists of AC power input, DC power input and relay output depend on different 
Model.
JetNet 6728G-24P-AC-2DC/6728G-16P-AC-2DC:

JetNet 6728G-24P-AC/6728G-16P-AC:

Package Check List

 

The Rack Mount Managed Ethernet Switch 

 

Console cable

 

Rack Mount kit

 

Power Cord (Depend on Country)

 

QIG

Overview

Interface Introduction

A Beijer Electronics Group Company

Installation

Mount the Switch to 19’’ rack

1. Attach the brackets to the device by using the 
screws provided in the Rack Mount kit.
2. Mount the device in the 19’’ rack by using four 
rack-mounting screws provided by the rack 
manufacturer.
3. When installing multiple switches, mount them in 
the rack one below the other.

Power the unit and connect to network Cable

AC Power Input: connect the attached power cord to the AC power input connector, the 
available AC power input is range from 90-264VAC.
DC Power Input: the suggested power input is 44-57VDC(IEEE 802.3af), 
50-57VDC(IEEE 802.3at).
Follow below steps to wire JetNet 6728G redundant DC power inputs. 
1. Insert positive and negative wires into V+ and V- contacts respectively of the terminal 
block connector.
2. Tighten the wire-clamp screws to prevent DC wires from being loosened.
3. DC1 and DC2 support polarity reverse protection functions.

Wiring Digital Output

JetNet 6728G series provides 1 digital output, also known as relay output. The relay contacts 
are energized (open) for normal operation and will close for fault conditions. The fault 
conditions include power failure, Ethernet port link break or other pre-defined events which 
can be configured in JetNet 6728G UI.

Wiring Earth Ground

To ensure the system will not be damaged by noise or any electrical shock, we suggest you to 
make exact connection with JetNet 6728G with earth ground.
For AC input, the 3 pin include V+, V- and GND. The GND pin must be connected to the 
earth ground. 
For DC input, loosen the earth ground screw by screw drive; then tighten the screw after 
earth ground wire is connected.

Note: 

Check if the rack environment temperature conforms to the specified operating 

temperature range. Do not place any equipment on top of the switch and please properly 
grounded.

24 100/1000Base-TX with 24 PoE Plus ports, 4 Gigabit SFP ports, Ind. full Gigabit 
Managed PoE Plus Ethernet Switch, -40~75°C, AC and dual DC power

24 100/1000Base-TX with 24 PoE Plus ports, 4 Gigabit SFP ports, Ind. full Gigabit 
Managed PoE Plus Ethernet Switch, -40~75°C, AC power

24 100/1000Base-TX with 16 PoE Plus ports, 4 Gigabit SFP ports, Ind. full Gigabit 
Managed PoE Plus Ethernet Switch, -40~75°C, AC and dual DC power

24 100/1000Base-TX with 16 PoE Plus ports, 4 Gigabit SFP ports, Ind. full Gigabit 
Managed PoE Plus Ethernet Switch, -40~75°C, AC power

Model Name

Description

JetNet 6728G-24P-AC

JetNet 6728G-24P-AC-2DC

JetNet 6728G-16P-AC-2DC

JetNet 6728G-16P-AC

1 AC power inputs, 2 DC power inputs and 1 relay output.

1 AC power inputs and 1 relay output.

1 AC power inputs, 2 DC power inputs and 1 relay output.

1 AC power inputs and 1 relay output.

JetNet 6728G-24P-AC-2DC

JetNet 6728G-24P-AC

JetNet 6728G-16P-AC-2DC

JetNet 6728G-16P-AC

Model Name

Back-Panel Components

LED

Color

Function 

PWR

Green

Power (1, 2, 3) on

Alarm

Red

Power failure, port failure, ping failure, 

login failure, RSR topology change

R.S.

Lit Green

MSR in normal state 

Lit Yellow

MSR in abnormal state 

Not Lit

MSR function not active 

Flashes Green

Incorrect configuration of MSR, ex. ring not 

connected to ring port 

Flashes 

Yellow

The break has been detected to be local to 

one of the ports 

Sys

Green

System on

G1-G24 Copper

af/at

Green

802.3af PoE Powering 

Blue

802.3at PoE Powering 

G1-G24 Copper

LNK/ACT

Lit Green

10/100/1000 RJ-45 Link

Flashes Green

10/100/1000 RJ-45 Activity

G1-G24 Copper

Speed 

Yellow on

1000Mbps

Yellow off

10/100Mbps

G25-G28 SFP 

LNK/ACT 

Lit Green

Link

Flashes Green

Activity

Reviews: