Behlen Country 80900240 Quick Start Manual Download Page 1

F-20864-2 

TECHNICAL INFORMATION 70160

 

Rev. 4-4-19   1-17-11

Tillage Discs

Sub Compact, Medium, & Heavy Duty

CUSTOMER SERVICE CENTER

 

PO Box 569 

Columbus, NE 68602-0569

Ph: 800-447-2751 

Fax: (402) 563-7447 

www.behlencountry.com

Hardware Kit

80900240

THANK YOU FOR PURCHASING THIS PRODUCT

Congratulations on your purchase.  Behlen Country has been in the business of providing 

quality equipment to landowners for more than 80 years.  Our 3-Point Equipment will provide 

many years of service when maintained by the operator and used in accordance with the 

capabilities of the product.  For questions about this product, or for parts inquiries, please 

contact our Customer Service Center listed below

TO THE CUSTOMER

This manual contains valuable information about 

your new Tillage Disc. It has been prepared to 

give you helpful suggestions for safety, operation, 

adjustment and service.  
It is the owner’s and or operator’s responsibility to:
• Read and understand the information contained 

in this manual. The use of this equipment is 

susceptible to certain hazards that cannot be 

protected against by mechanical means or 

product design.  All operators of this equipment 

must read and understand this entire manual, 

paying particular attention to safety and 

operating instructions, prior to using.

• Assemble, operate and maintain the equipment 

in accordance with all instructions and safety 

procedures in this manual.

• Inspect the equipment prior to each use and 

replace or repair any parts that are worn or 

damaged.

STATEMENT OF POLICY

It is the policy of Behlen Country to improve its products where it is possible and practical to do so. 

Behlen Country reserves the right to make changes or improvements in design and construction at any 

time, without incurring the obligation to make these changes on previously manufactured units.

Summary of Contents for 80900240










Reviews: