background image

Installation and Technical Information

BEGA

Accessories

Please refer to the appropriate

accessory installation sheet for

further instruction when applicable.

Replacement Parts

In the interest of product improvement, BEGA reserves the right to make technical changes without notice.

BEGA  

1000 Bega Way, Carpinteria, CA 93013 (805)684-0533 Fax (805)566-9474 www.bega-us.com © Copyright BEGA-US 2017

(5/16" - 18 x 10")

LED Bollard

88 066

Tools Required:

Adjustable wrench

1/2” nut driver

3mm hex key

4mm hex key

5mm hex key

Protection Class: 

IP 65

Weight:

  20.3 lbs.

Relamping/Maintenance

No relamping required.

Lamp:

   7.9W LED

    88 066 

6/21/2017 

Page 1 of 2

Anchorage 

79 817

Notice to Installer for 88 066:

1. See page 2 for specific product safety warnings.

2. Fixture may be damaged if connected to conduit systems that contain water - Article 300-5G of                       

    the National Electric Code requires that “Conduits or raceways through which moisture may contact  

     

    energized live parts shall be sealed or plugged at either or both ends.”

3. 79 817 anchorage kit (included) must be installed in concrete pad/foundation.

4. It is recommended that when installing in planting areas the bollard base be slightly elevated to  

    

    avoid prolonged submerging during heavy rains.

5. Wet location listing does not imply suitability for exposure to standing water for long periods of time.

6. LEDs are high-quality electronic components! Please avoid touching the light 

    output opening of the LED directly during installation.

79 817 anchorage installation:

1. Provide means to bring supply wiring to the bollard in accordance with local code.  The template has  

     

    a 2-3/8” conduit hole for conduit entry.

2. Assemble anchorage kit.  Unscrew the (3) hex bolts from the female couplers.  Remove each hex  

 

    bolt and washer.  Align each anchor bolt with the hole in the template.  Attach each anchor bolt to 

    the template by replacing the washer and hex bolt and tightening.

3. Determine the finished grade for the application.  Use leveling hardware to adjust template to      

     

    desired finished height after pouring.

4. Install anchorage kit using either method:

 

A. Attach template to forming or cross bracing using the (2) nail holes  

 

 

 

 

    provided in the template.  Level template properly.  Pour concrete.

 

B. Insert anchorage assembly into poured concrete.  Concrete must be  

 

 

 

     

    vibrated to ensure proper anchorage setting.  Level template properly. 

88 066 installation:

1. Remove (3) hex bolts and washers, once anchorage is set.

2. Leave template in place to provide a smooth, flat surface to mount the base.

3. Loosen (4) 4mm set screws on lower side of fixture main casting to remove the main casting from  

 

    lower casting. NOTE: The lower casting resides inside the main casting and connects directly to  

 

    the bollard base.

4. Loosen the 5mm set screw on the lower casting and remove the bollard base.

5. Align bollard base holes with anchorage holes.

6. Bolt the bollard base to the anchorage kit using the (3) hex bolts and washers. 

7. Make supply wiring connections to wire leads from driver inside the fixture

 

MAIN VOLTAGE SUPPLY WIRE TO BLACK LUMINAIRE WIRE; 

 

NEUTRAL (COMMON) SUPPLY WIRE TO WHITE LUMINAIRE WIRE; 

 

GREEN GROUND WIRE TO GREEN LUMINAIRE WIRE.

    Dimming (if applicable):

 

DIMMING CONTROL WIRE (+) TO POSITIVE DRIVER DIM CONTROL WIRE

 

DIMMING CONTROL WIRE (-) TO NEGATIVE DRIVER DIM CONTROL WIRE

8. Place the lower casting over the bollard base so that the (3) notches in the bollard base align with the lower  

    casting and orient correctly. Attach together by tightening the 5mm set screw.

9. Secure the bollard by tightening the (4) 4mm set screws at the base of the main casting.

Dimensions
A:

   10-5/8 “

B:

   28-1/8 “

C:

   5-1/4 “

Description

Lens

Driver (120V-277V)

LED (3000K)

LED (4000K)

Part No

Consult factory

75983-02

LED-0322/930

LED-0322/940

Figure 1

Figure 2: Anchorage Assembly

Figure 3: Generic Image

Main Casting

Lower Casting

Bollard Base

Reviews: