manualshive.com logo in svg

Beckman Coulter Microfuge 20 Series, Instructions For Use Manual

Share
Download
Beckman Coulter Microfuge 20 Series Instructions For Use Manual Download Page 40

B30162AA

2-10

Operation

Run Procedure  

To activate only the Soft-stop function 

1

Press the 

MENU

 key until the 

Soft-stop/start

 function flashes on the display.

Program mode ends if no other keys are pressed within 15 seconds.

2

Press the 

 or 

 cursor key until the 

Soft stop on

 is displayed.

The soft-stop function is now activated.

3

Press the 

MENU

 key to confirm the selection. 

To deactivate both Soft-start and Soft-stop functions 

1

Press the 

MENU

 key until the 

Soft-stop/start

 function flashes on the display.

Program mode ends if no other keys are pressed within 15 seconds.

2

Press the 

 or 

 cursor key until the 

Soft off

 is displayed.

Both soft functions are now deactivated.

3

Press the 

MENU

 key to confirm the selection. 

Starting a Run

The run can be started using the parameters in memory from a previous run, or using new or 
changed parameters that you enter using the procedures described above.

To start a run

1

Check that all parameters are correct and the door is closed and latched.

2

Press the 

START/STOP

 key.

 •

An actual set speed greater than the rotor’s maximum permitted speed, results in an error 
code and the centrifuge shuts down. 

—

See 

CHAPTER 3, 

Troubleshooting

 for information on error codes. 

Summary of Contents for Microfuge 20 Series











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands