background image

Foreword

PS2001-2440-0000

7

Version: 1.0

2.2

Safety instructions

Description of instructions

In this documentation the following instructions are used. 
These instructions must be read carefully and followed without fail!

 DANGER

Serious risk of injury!

Failure to follow this safety instruction directly endangers the life and health of persons.

 WARNING

Risk of injury!

Failure to follow this safety instruction endangers the life and health of persons.

 CAUTION

Personal injuries!

Failure to follow this safety instruction can lead to injuries to persons.

NOTE

Damage to environment/equipment or data loss

Failure to follow this instruction can lead to environmental damage, equipment damage or data loss.

Tip or pointer

This symbol indicates information that contributes to better understanding.

Intended use

This device is designed for installation in a housing and is intended for general professional use, for example
in industrial control systems or office, communication and measuring equipment.

Do not use this power supply in installations where a malfunction could cause serious injury or danger to
human life.

Exclusion of liability

All the components are supplied in particular hardware and software configurations appropriate for the
application. Modifications to hardware or software configurations other than those described in the
documentation are not permitted, and nullify the liability of Beckhoff Automation GmbH & Co. KG.

Personnel qualification

This description is only intended for trained specialists in control, automation and drive engineering who are
familiar with the applicable national standards.

Safety regulations

Please note the following safety instructions and explanations!
Product-specific safety instructions can be found on following pages or in the areas mounting, wiring,
commissioning etc.

Summary of Contents for PS2001-2440-0000































Reviews: