Beckhoff EL5032 Documentation Download Page 137

Page: 137 / 142

Appendix

EL5032, EL5032-0090

137

Version: 2.4

• Select the file (*.rbf) with the new FPGA firmware, and transfer it to the EtherCAT device:

• Wait until download ends

• Switch slave current less for a short time (don't pull under voltage!). In order to activate the new FPGA

firmware a restart (switching the power supply off and on again) of the EtherCAT device is required.

• Check the new FPGA status

NOTE

Risk of damage to the device!

A download of firmware to an EtherCAT device must not be interrupted in any case! If you interrupt this
process by switching off power supply or disconnecting the Ethernet link, the EtherCAT device can only be
recommissioned by the manufacturer!

8.2.5

Simultaneous updating of several EtherCAT devices

The firmware and ESI descriptions of several devices can be updated simultaneously, provided the devices
have the same firmware file/ESI.

Fig. 127: Multiple selection and firmware update

Select the required slaves and carry out the firmware update in BOOTSTRAP mode as described above.

Summary of Contents for EL5032















































































































































Search results

Summary of Contents for EL5032

Reviews:

Related manuals for EL5032

Brands by name

Popular brands

Beckhoff EL5032, Documentation

Search results

Summary of Contents for EL5032

Reviews:

Related manuals for EL5032

Brands by name

Popular brands