background image

General Notes 

 

 

 
 

Basic safety measures 

Only switch the PC off after 
closing the software 

Before the Industrial PC is switched off, software that is running must 
be properly closed. 

 

Otherwise it is possible that data on the hard disk is lost. Please read the 
section on 

Switching the Industrial PC on and off

 

 

Warning

 

 

Switch off all parts of the equipment, then uncouple the fieldbus! 

Before opening the housing of the PC, and whenever the PC is being used 
for purposes other than plant control, such as during functional tests 
following repair, all parts of the equipment must first be switched off, after 
which the Industrial PC can be uncoupled from the plant. 

 

Pulling out the fieldbus connection plug uncouples the PC (optional). 

 

Items of equipment that have been switched off must be secured against 
being switched on again. 

 

 

 

 

The Industrial PC’s power supply unit must be supplied with 24 V

DC

 

 

 

Do not exchange any parts when under power! 

When components are being fitted or removed, the supply voltage must be 
switched off. 

 

Fitting work on the Industrial PC can result in damage: 

• 

If metal objects such as screws or tools fall onto operating circuit 
boards. 

• 

If connecting cables internal to the PC are removed or inserted 
during operation. 

• 

If plug-in cards are removed or inserted when the PC is switched 
on. 

 

 

4

 

 CP71xx 

Summary of Contents for CP71 Series
























Reviews: