background image

Product Description 

 

 

10

 

C5210 

2.4.1  USB Interfaces (X112, X113) 

The two USB interfaces (

X112

X113

) are used for connecting peripheral devices with USB connection. 

USB2.0 standard

 

is supported. 

2.4.2  ATX Push-button 

The Industrial PC is switched on via the push-button (

ATX

) (Power on). 

2.4.3  Reset-button  

The reset-button enables re-booting the Industrial PC. 

2.4.4  Status LEDs 

 

The LED 

HDD

 is illuminated  at HDD access. 

 

The LED 

PWR

 is illuminated  when power is on. 

 

The LED 

FB

 is a multi color LED and shows the status of fieldbus and TwinCAT: 

 

Color LED FB 

Description 

red 

TwinCAT STOP 

blue 

TwinCAT CONFIG 

blue/ red blinking 

TwinCAT CONFIG with Bus Error 

green 

TwinCAT RUN 

green/ red blinking 

TwinCAT RUN with Bus Error 

 

2.5  Rear view of the C5210 

The C5210 Industrial PC is fitted with a 100-240 V, 50-60 Hz full range power supply unit. 

Optional a 24 V

DC 

 power supply unit with UPS is available. 

 

2.5.1  100-240V

AC

 Full Range Power Supply 

Rear view C5210 
with 100-240V

AC

 full range 

power supply 

 

 

interfaces 

PCIe module slots 

power supply 

battery, optional fieldbus 

main switch 

Summary of Contents for C5210


































Reviews: