Beckhoff AM8000 Series Operation Instructions Manual Download Page 86 | Manualshive

Page: 86 / 123

background image

Technical description

86

───

Version: 4.3

AM8000 and AM8500

7.5

Power derating

Derating may be necessary at high ambient temperature or when
operating at a great height above sea level. In addition, some mo-
tors may experience power reductions depending on the feedback
system installed or the holding brake [+]. The reduction affects the
standstill current and the standstill torque.

Ambient temperature

fT = Temperature utilization factor

tA = Ambient temperature in °C

Calculation of the performance data if the specified temperature limit
> 40 °C to 55 °C is exceeded:

M0_red = M0 x fT

Installation altitude

fH = Altitude utilization factor

h = Altitude in meters

Calculation of the performance data if the specified installation alti-
tude is exceeded > 1000 m to 3000 m:

M0_red = M0 x fH

Ambient temperature and installation altitude

Calculation of the power data when exceeding the specified limits:

Ambient temperature > 40 °C, altitude > 1000 m and < 3000 m:

M0_red = M0 x fT x fH

«
...
84
85
86
87
88
...
»

Summary of Contents for AM8000 Series




























































































































Reviews:

No comments

Related manuals for AM8000 Series

Brand: VAR-SPE Pages: 80

Brand: EuroLite Pages: 19

Brand: EBARA Pages: 36

Brand: Stuart Turner Pages: 20

X Trainer 300 2T 2015

Brand: Beta Motorcycles Pages: 117

Brand: YARDMAX Pages: 25

Brand: Tanaka Pages: 7

Brand: WEICHAI Pages: 33

Brand: WEG Pages: 68

Brand: Cobra Garden Machinery Pages: 64

Brand: Louvolite Pages: 4

Brand: Volvo Pages: 72

Brand: HAMPTON BAY Pages: 17

Brand: Yanmar Pages: 65

Brand: Yanmar Pages: 316

Brand: Honda Pages: 2

Brand: Honda Pages: 32

Brand: Honda Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands